Jumping Ring Lab · Guide · glidepathscience.org
GuideJumping Ring Lab
Contents
This Guide explains the ideas and equations behind every Walkthrough step, Concept Challenge question and Predict round, in the order a textbook would take them. Part 1 prepares the Intro track and Part 2 the Advanced track; each takes about fifteen minutes to read. Each section ends with a worked example that is not one of the sim's own problems.
Part 1 · The essentials
Math you’ll need: algebra, sines and cosines, exponentials and natural logarithms, and the right-hand rule; calculus only in a box marked “With calculus.”
A ring that is not magnetic
In 1887 Elihu Thomson showed an audience a coil wound round an iron rod that stuck up out of it, with a ring of aluminum slipped over the rod. When he switched on the alternating current, the ring shot into the air. The demonstration still surprises people, because aluminum is not magnetic: a refrigerator magnet slides right off a soda can. Whatever throws the ring, it is not the attraction or repulsion of magnetized metal.
The explanation is a chain of three steps. The current in the coil drives a magnetic flux up the iron rod, and because the current alternates, the flux through the ring keeps changing. A changing flux drives an electromotive force (EMF) around any closed path that encircles it. The ring is such a path made of metal, a circuit of one turn, so the EMF drives a large current around it. And a current in a magnetic field feels a force: the coil's field pushes on the current the coil itself induced. Any good conductor will do; the ring's metal matters through how well it conducts and how much it weighs.
Weight matters because the push has to beat it. A ring of density $\rho_m$, height $h$, outer radius $a_{out}$ and inner radius $a_{in}$ has mass and weight
$m = \rho_m\,\pi(a_{out}^2 - a_{in}^2)\,h$ $W = mg$
The common mistake is to picture the rod magnetizing the ring, so that like poles repel. An iron ring would be magnetized, and that pulls it toward the coil rather than throwing it off. A plastic ring would sit still. Only a conducting ring jumps, and only while the current changes.
Everything starts with the flux, so that is where the story begins.
Faraday's law: an EMF round the ring
The magnetic flux $\Phi$ through a surface measures how much magnetic field passes through it: for a uniform field $B$ crossing an area $A$ at right angles, $\Phi = BA$, in webers (1 Wb = 1 T·m²). Most of the coil's flux runs up the iron rod, so the flux through the ring is mostly the flux the rod carries at the ring's height.
Faraday's law says that a changing flux drives an EMF around any closed path that surrounds it, equal to the rate at which the flux changes. If the flux changes by $\Delta\Phi$ in a short time $\Delta t$,
$\varepsilon = -\dfrac{\Delta\Phi}{\Delta t}$
The path need not be a wire. The coil's changing flux drives an EMF round an empty loop in space, and round a ring with a saw cut through it, as much as round a whole ring; what the cut removes is the current. The minus sign records the direction, the subject of Lenz's law below.
With alternating current the flux swings as a sine wave of frequency $f$ and amplitude $\hat{\Phi}$, written with the angular frequency $\omega = 2\pi f$: $\Phi(t) = \hat{\Phi}\sin\omega t$. Its rate of change behaves like the velocity of a mass on a spring, whose top speed is ωA for an amplitude A. So the EMF is a sine wave of the same frequency, a quarter cycle (90°) behind the flux, with amplitude
$\hat{\varepsilon} = \omega\hat{\Phi} = 2\pi f\hat{\Phi}$
Two mistakes are common. The first is to expect the largest EMF when the flux is largest. The EMF follows the slope of the flux, not its size: at the flux's peak the slope is zero, and the EMF is largest as the flux passes through zero. The second is to multiply the flux by $f$ instead of $\omega$, which loses a factor of 2π.
A quarter of a volt sounds feeble. The next section shows why it is not.
A circuit of one turn
A conductor of resistivity $\rho$, length $L$ and cross-sectional area $A$ has resistance $\rho L/A$. In a ring the current goes all the way round, a path as long as the circumference at the middle of the wall, $2\pi a$, where $a$ is the mean radius, and it flows through the wall's section, the thickness $t$ times the height $h$:
$R_2 = \rho\,\dfrac{2\pi a}{t\,h}$
The subscript 2 marks the ring, the second circuit; the coil is circuit 1. A thick band of good metal has a resistance of a fraction of a milliohm, so even a small EMF drives hundreds of amperes. Resistance is not all that holds the current back, though: the ring also has inductance, which opposes changes in its own current, so its actual current is smaller than $\hat{\varepsilon}/R_2$, and later. That delay, as the section on alternating current shows, is what makes the ring jump.
Three slips are common: using the radius $a$ for the path instead of the circumference $2\pi a$, which makes the resistance six times too small; dividing by the area of the ring's flat face instead of the section the current crosses, $t\,h$; and dividing an EMF in volts by a resistance in microhms ($1\,\mu\Omega = 10^{-6}\,\Omega$).
Large currents, then. But which way do they flow?
Lenz's law: which way the current flows
Lenz's law gives the direction: the induced current flows the way that makes its own field oppose the change in flux that drives it. If the flux through the ring is growing, the ring current makes flux the other way, circulating opposite to the coil current. If the flux is shrinking, the ring current props it up, circulating the same way as the coil current. This is the minus sign in Faraday's law, and it is energy conservation too: a current that helped the change along would feed itself and create energy from nothing.
Currents that circulate the same way attract, and currents that circulate in opposite senses repel. So a growing coil current pushes the ring away, and a shrinking one pulls it in. A sense of circulation means something only from a stated place, so this sim names it by the rod's axis: "seen from +z", looking down the rod from above.
Direct current shows the rule most plainly. Close a switch on a DC supply $V$ and the coil current rises over the coil's time constant, set by its inductance and resistance, toward $V/R_1$:
$I_1(t) = \dfrac{V}{R_1}\left(1 - e^{-t/\tau_1}\right)$ $\tau_1 = L_1/R_1$
While it rises, the flux grows and the ring is pushed. Once it is steady, nothing is induced and there is no force at all, however large the current. When the switch opens, the current collapses in a millisecond or so, and the ring current reverses to oppose the fall: a brief, sharp pull toward the coil.
The usual mistake is to remember Lenz's law as "the ring current is always opposite to the coil current". It opposes the change: when the coil current falls, the ring current runs with it.
A current in a magnetic field feels a force. Its direction holds the next surprise.
Why the field has to flare
A short piece of wire $\Delta\vec{\ell}$, pointing along the current $I$, in a field $\vec{B}$ feels a force $\Delta\vec{F} = I\,\Delta\vec{\ell}\times\vec{B}$, perpendicular to both. Split the field at the ring into a vertical part $B_z$ and a radial part $B_r$, pointing straight out from the axis. Around the ring $\Delta\vec{\ell}$ is horizontal and tangent to the circle. Crossed with $B_z$, it gives a force straight in or out; around the ring these squeeze or stretch it and cancel, so a uniform vertical field, however strong, cannot lift a flat ring. Crossed with $B_r$, it gives a vertical force, the same on every piece, and these add. Over the whole circumference
$F = I_2\cdot 2\pi a\cdot B_r$
A radial field exists only where the field lines spread out. Inside a long coil the lines run straight and parallel. At the top of this coil the flux leaks out of the rod's sides, and since field lines cannot simply end, a field that weakens upward must bend outward. That flare, just above the coil where the ring rests, is where the push comes from.
The mistake to avoid is thinking that the strongest field gives the biggest push. Deep inside a long coil, where $B$ is largest, a ring would feel no lift at all.
With alternating current, they rarely are.
Alternating current: why the push keeps its sign
At 60 Hz both currents reverse 120 times a second, and one might expect the push to reverse too and average to nothing. It does not, because the push depends on the product of the two currents. The coil's field at the ring is proportional to the coil current, so the push can be written $F = -k\,I_1 I_2$, where $k = 2\pi a B_r/I_1$ is a positive constant of the geometry and the minus sign says that opposite currents push. When both currents reverse together, their product keeps its sign.
How long the push lasts depends on how far the ring current is behind the coil current. Exactly opposite, half a cycle (180°) behind, the ring would be pushed at every instant. A quarter cycle (90°) behind, it would be pushed half the time and pulled half the time, averaging zero. The real ring sits in between. For two sine waves of amplitudes $\hat{I}_1$ and $\hat{I}_2$, the second a phase $\theta$ behind the first, the push lasts a fraction $\theta/180°$ of each cycle and averages
$⟨F⟩ = -\tfrac{1}{2}\,k\,\hat{I}_1\hat{I}_2\cos\theta$
which is a net push whenever $\theta$ is more than 90°.
The mistake is to reason that because each current averages to zero, so does the force. A product of two signals can have an average even when neither does.
Why is the real lag more than 90°? The coil current makes the flux, and the ring's EMF follows the flux's rate of change, so the EMF is a quarter cycle (90°) behind the coil current. A ring with resistance alone would carry a current in step with its EMF, 90° behind the coil current, and be pushed and pulled equally: a nichrome ring, a poor conductor, barely moves. But the ring's inductance opposes changes in its current, so the current falls a further angle φ behind its own EMF, and $\theta = 90° + \varphi$. The smaller the ring's resistance compared with its inductance, the larger φ, and the closer θ comes to 180°, where the push lasts the whole cycle.
What a student can change is the ring.
Better rings: metal, cold and weight
How high a ring jumps depends on its push compared with its weight. A ring that conducts better carries more current and lets it lag further behind, closer to 180°, so it is pushed harder. But the push has to lift the ring, and the best conductors are not the lightest metals. Copper conducts nearly twice as well as the sim's aluminum alloy, yet it is 3.32 times as dense, and its larger push does not make up for that: an aluminum ring jumps higher than a copper one of the same size. That is why demonstration rings are aluminum.
Cooling helps more than any choice of metal. In liquid nitrogen, at 77 K, Tjossem and Brost measured the resistivity of their aluminum rings falling by a factor of 4.0 and of their copper rings by 6.7, with no change in mass. The cold ring carries more current, lags further, is pushed several times as hard, and flies several times as high. The gain has a limit, though: once the lag is close to 180°, the ring current is already nearly opposite to the coil current at every instant, and less resistance adds little.
The tempting mistake is to rank rings by conductivity alone. The best conductor gets the biggest push, but compare each ring's push with its own weight.
Turn the voltage down and the push may not throw the ring at all. It can still hold it up.
Turn it down and it floats
Both currents grow in proportion to the supply voltage, so the average push grows as $V^2$. It also weakens as the ring rises out of the flare. At a low enough voltage the ring rises only until the average push equals its weight, and there it floats, buzzing slightly at twice the supply frequency. The float is stable: if the ring rises, the push falls below its weight and it sinks back; if it sinks, the push grows and lifts it.
Over the first several centimeters this sim's push is well described by an exponential with a decay length $\ell$, $⟨F⟩ \approx F_0\,e^{-z/\ell}$, where $z$ is the height above the plate and $F_0$ the fitted exponential's value there (close to, but not exactly, the true push at the plate). Setting $⟨F⟩ = mg$ gives the float height, here to within a few millimeters:
$z_{float} = \ell\ln\dfrac{F_0}{mg}$
A common misconception is that a ring pushed twice as hard floats twice as high. Because the push falls off exponentially, quadrupling it adds only $\ell\ln 4$ to the height.
Part 2 · Going further
Math you’ll need: derivatives and partial derivatives, two coupled differential equations in outline, integrals over time, and complex numbers (phasors).
Two coupled circuits
The coil and the ring are two circuits linked by a mutual inductance $M$: the flux the coil puts through the ring is $M I_1$, and the flux the ring puts through the coil is $M I_2$, with the same $M$ both ways. Each also links its own flux through its self-inductance, $L_1$ or $L_2$. Faraday's law applied to each circuit gives its equation. The ring moves, though, and $M$ depends on its height $z$, so the rate of change of $M I_1$ has two parts, $M\dot{I}_1$ and $I_1(\partial M/\partial z)\,v$, where $v = \dot{z}$; $L_2$ also depends on how much iron sits inside the ring. In full,
$L_1\dot{I}_1 + M\dot{I}_2 + v\,\dfrac{\partial M}{\partial z}I_2 = V(t) - R_1 I_1$
$M\dot{I}_1 + L_2\dot{I}_2 + v\,\dfrac{\partial M}{\partial z}I_1 + v\,\dfrac{\partial L_2}{\partial z}I_2 = -R_2 I_2$
together with Newton's second law for the ring, $m\ddot{z} = F - mg - \text{drag}$. The terms that contain $v$ are the motional EMFs. Moved to the right-hand side, $-v\,(\partial M/\partial z)\,I_1$ is the EMF $\oint(\vec{v}\times\vec{B})\cdot d\vec{\ell}$ of a conductor moving through a field, $v\cdot 2\pi a B_r$ for a ring rising through the flare. It opposes the motion, and through these terms the circuits pay for the work done on the ring. The sim integrates the whole set with fourth-order Runge–Kutta, at 240 or more steps per cycle.
The mistake is to drop the motional terms because they look small. Without them the books do not balance: the ring would gain kinetic energy that no circuit supplied.
The circuit equations say how the currents evolve. The force comes from the energy stored between them.
The force from the co-energy, and flux cutting
The magnetic energy stored by two coupled circuits is $W_B = \tfrac{1}{2}L_1 I_1^2 + M I_1 I_2 + \tfrac{1}{2}L_2 I_2^2$. For inductances that do not depend on the currents, the co-energy $W′$ is this same expression, and the force on the ring is its rate of change with height at fixed currents:
$F = \left.\dfrac{\partial W′}{\partial z}\right|_{I} = I_1 I_2\,\dfrac{\partial M}{\partial z} + \tfrac{1}{2}I_2^2\,\dfrac{\partial L_2}{\partial z}$
Above the coil, $M$ falls as the ring rises, so $\partial M/\partial z < 0$, and the first term pushes the ring up only when $I_1 I_2 < 0$, with the currents circulating in opposite senses: the Intro's "opposite currents repel" as an equation. The second term comes from the iron. The ring's self-inductance is larger with more of the rod inside it, so $\partial L_2/\partial z < 0$ near the rod's top, and since $I_2^2$ is never negative, this term always pulls the ring back. Here it is small.
The co-energy force and Part 1's $I_2\cdot 2\pi a\cdot B_r$ must be the same force, and flux cutting shows why. As the ring rises by $dz$ it sweeps out a band of area $2\pi a\,dz$. Field lines cannot end, so flux that stops threading the ring must cross that band, and the flux crossing it is $2\pi a B_r\,dz$. The flux through the ring, $M I_1$, therefore changes as
$\dfrac{\partial M}{\partial z} = -\dfrac{2\pi a B_r}{I_1}$
and $I_1 I_2\,\partial M/\partial z = -I_2\cdot 2\pi a\cdot B_r$, the sum of $I\,d\vec{\ell}\times\vec{B}$ around the ring, at every instant.
A common slip is to think the sign of $\partial M/\partial z$ alone decides push or pull. It fixes the geometry; the sign of $I_1 I_2$ decides the direction from instant to instant.
Over a cycle of AC, what matters is how the two currents line up in time. Phasors handle that neatly.
The phase lag and the sin²φ law
In steady AC, with the ring held still, every quantity is a sine wave of the supply frequency, written as a complex amplitude, a phasor. The ring is then a series R–L circuit driven by the EMF the coil induces, $-j\omega M I_1$, a quarter cycle behind the coil current:
$I_2 = \dfrac{-j\omega M I_1}{R_2 + j\omega L_2}$ $\tan\varphi = \omega L_2/R_2$ $\tau_2 = L_2/R_2$
The ring current lags its own EMF by $\varphi$, and so lags the coil current by $90° + \varphi$: Part 1's $\theta$, more than a quarter cycle. The ring's time constant gives the same angle, $\tan\varphi = \omega\tau_2$. Putting the phasors into the average of the first force term gives a clean result:
$⟨F⟩ = \tfrac{1}{2}|I_1|^2\,\dfrac{M\,|\partial M/\partial z|}{L_2}\,\sin^2\varphi$
The limits explain the demonstration. A purely resistive ring, $\varphi$ = 0, carries a current a quarter cycle behind $I_1$, is pushed and pulled equally, and goes nowhere; a nichrome ring comes close to that. A ring with no resistance, $\varphi$ = 90°, carries a current exactly opposite to $I_1$ and gets the largest push a ring of its shape can get. At a fixed coil current, less resistance, a higher frequency or a colder ring all raise $\varphi$ and the push. With the variac fixed, though, a higher frequency also cuts the coil current, roughly as $1/f$, and the push falls. A good conductor also loads the coil, canceling part of its reactance, so the coil current rises too, and a cold ring gains on both counts.
The classic mistake is to expect less resistance to give proportionally more push. The push follows $\sin^2\varphi$, which climbs steeply at small lags and saturates near 90°.
Raising $\varphi$ by making the ring taller has a cost, though: a taller ring is heavier.
The best ring
Tjossem and Brost asked which ring of a given metal jumps highest. Make the ring taller and its resistance falls as $1/h$ while its mass grows as $h$. Its self-inductance changes much less, so $\tan\varphi = \omega L_2/R_2$ grows in proportion to $h$. At a fixed coil current the push per kilogram then goes as $\sin^2\varphi/h$, which is proportional to
$\dfrac{\sin^2\varphi}{\tan\varphi} = \sin\varphi\cos\varphi = \tfrac{1}{2}\sin 2\varphi$
largest at $\varphi$ = 45°, where $R_2 = \omega L_2$. Starting from a ring of height $h$ and resistance $R_2$, the best height is
$R_2 = \omega L_2$, so $h^{∗} = h\,R_2/\omega L_2$
The same condition marks the ring's greatest heating at a fixed coil current, since $\tfrac{1}{2}|I_2|^2 R_2 = \tfrac{1}{2}(\omega M|I_1|)^2 R_2/(R_2^2 + \omega^2 L_2^2)$ is largest at $R_2 = \omega L_2$: the dashed curve's peak above. Tjossem and Brost found the best jumps near a lag of 45°. The argument is a guide rather than a law, since it holds the coil current fixed and ignores the slow change of $L_2$ and $M$ with height, and the full simulation's best ring sits a little away from 45°.
The usual slip is to invert the ratio. A ring whose resistance is above its reactance should be made taller, to bring $R_2$ down to $\omega L_2$; one below it, shorter.
Even the best ring turns very little of the supply's energy into flight.
Where the energy goes
Energy conservation keeps exact books. The energy the supply delivers, $\int V I_1\,dt$, goes into heat in the coil, $\int I_1^2 R_1\,dt$, heat in the ring, $\int I_2^2 R_2\,dt$, energy stored in the magnetic field, and the work the magnetic force does on the ring, $\int F v\,dt$. That work becomes the ring's kinetic energy $K = \tfrac{1}{2}mv^2$, its gravitational energy $U_g = mgh$, and losses to rubbing and air drag. The motional EMFs tie the circuit books to the mechanical ones, and the sim keeps both as it runs.
The books are lopsided: coil and ring are heated hard, and only a sliver of the supply's energy ends up in the flying ring, a superb demonstration and a terrible engine.
The mistake is to count only kinetic energy. By the time the sim's ring leaves the rod it is about 14 cm higher than it started, and its gravitational energy is then larger than its kinetic energy.
Folklore says the jump improves if you choose when to close the switch.
The switching moment
In steady AC the current in an inductive coil runs nearly a quarter cycle behind its voltage, but when the switch closes the current must start from zero. Close it at a zero of the voltage, where the steady current would be at its negative peak, and the current makes up the difference with a DC offset of nearly a full peak, which dies away with the coil's time constant. Close it at a peak of the voltage, where the steady current would be zero anyway, and there is no offset. The offset nearly doubles the first peak of the coil current, and with it the first push on the ring:
offset $\propto e^{-t/\tau_1}$ $\tau_1 = L_1/R_1$
Whether that helps the jump depends on the ring. A light ring pushed hard early moves up the rod into weaker field and may collect less of the steady push that follows; a ring that leaves the rod within $\tau_1$ or so keeps the benefit. The sim lets you try both.
The mistake is to treat "close at a zero for the biggest jump" as a rule. The biggest first push does not guarantee the highest jump.
Once the switching is over and a ring floats, its height becomes something to measure.
A stable float, measured
Part 1's exponential, $⟨F⟩ = C V^2 e^{-z/\ell}$, makes the float height a simple function of the voltage. Setting the push equal to $mg$ at two voltages and dividing gives
$z_2 = z_1 + \ell\ln(V_2^2/V_1^2)$
Read the other way, $\ln V^2 = \ln(mg/C) + z/\ell$: plotted against the float height, $\ln V^2$ is a straight line of slope $1/\ell$, which is what the Hover Bench measures. The float is stable because $d⟨F⟩/dz = -⟨F⟩/\ell < 0$ there. In this model $\ell$ is about 3 cm. The push goes as $M\,|\partial M/\partial z|$; here $M$ and $|\partial M/\partial z|$ each fall off over 6 to 7 cm, so their product falls off over about 3.3 cm, all of it set by the leakage length the model assumes for the iron rod. The exponential is a local fit, good to a millimeter or so over the heights it was fitted to, not a law.
The commonest slip is to use $\ln(V_2/V_1)$. The push goes as $V^2$, so the logarithm is of the ratio of squares, twice as large.
Every model has edges, and the last section finds this one's.
Where the model ends: skin depth and saturation
The model spreads the ring current evenly through the 3.18 mm wall. An alternating current is in fact pushed toward a conductor's surfaces by its own changing field, falling off over the skin depth
$\delta = \sqrt{2\rho/\mu_0\omega}$
where $\mu_0$ = 4π × 10⁻⁷ H/m. When $\delta$ is several times the wall, an even current is a good approximation. When it is about the wall or less, the current crowds to the surfaces, the real resistance is higher than the model's, and the model overstates the push. Good conductors, low temperatures and high frequencies all shrink $\delta$, so cold copper is the first ring to break the model.
The iron has an edge too. A real core saturates near 1.5 to 2 T: past that it no longer multiplies the field, and the coil draws far more current than the model shows. The core field goes as $V/f$, so high voltage at low frequency is the danger, and the Sandbox warns above 1.5 T. The model also leaves out losses in the iron, the ring tilting on the rod and the coil heating up; the Field Manual lists every assumption.
The mistake to avoid is trusting a number from outside a model's domain: a simulation always gives an answer, meaningful or not.
Reference
Common mistakes
Part 1
- Thinking the ring is magnetized. Any conductor jumps; the push acts on the induced current.
- Expecting the largest EMF at the largest flux. The EMF follows the slope of the flux, $\hat{\varepsilon} = 2\pi f\hat{\Phi}$.
- Using the radius as the current's path. The current goes around the circumference: $R_2 = \rho\,2\pi a/(t h)$.
- "The ring current is always opposite." It opposes the change in flux: a falling coil current gives a ring current with it, and a pull.
- Looking for lift in the vertical field. Only the radial part, where the field flares, lifts a flat ring.
- Expecting AC to average to zero. The push goes as $I_1 I_2$, and both reverse together.
- Ranking rings by conductivity alone. Compare each ring's push with its weight.
Part 2
- Expecting push in proportion to $1/R$. At a given coil current the push follows $\sin^2\varphi$.
- Using $\ln(V_2/V_1)$ for a float. The push goes as $V^2$.
Equation sheet
| Part 1 | |
|---|---|
| ring | $m = \rho_m\,\pi(a_{out}^2 - a_{in}^2)\,h$, weight: $mg$, with $g$ = 9.81 m/s² |
| Faraday | $\varepsilon = -d\Phi/dt$, so $\hat{\varepsilon} = 2\pi f\hat{\Phi}$ |
| ring resistance | $R_2 = \rho\,2\pi a/(t h)$ |
| Lenz; DC | the induced current opposes the change in flux; $\tau_1 = L_1/R_1$ |
| push on the ring | $F = I_2\cdot 2\pi a\cdot B_r$ |
| AC | $⟨F⟩ = -\tfrac{1}{2}k\hat{I}_1\hat{I}_2\cos\theta$, pushing $\theta/180°$ of each cycle |
| float | $z_{float} = \ell\ln(F_0/mg)$ |
| Part 2 | |
|---|---|
| motional EMF | $-v\,(\partial M/\partial z)\,I_1 = v\cdot 2\pi a B_r$ |
| force | $F = I_1 I_2\,\partial M/\partial z + \tfrac{1}{2}I_2^2\,\partial L_2/\partial z$ |
| flux cutting | $\partial M/\partial z = -2\pi a B_r/I_1$ |
| lag | $\tan\varphi = \omega L_2/R_2$, $\tau_2 = L_2/R_2$ |
| average | $⟨F⟩ = \tfrac{1}{2}|I_1|^2(M|M′|/L_2)\sin^2\varphi$ |
| best ring | $R_2 = \omega L_2$, so $h^{∗} = h\,R_2/\omega L_2$ |
| float | $z_2 = z_1 + \ell\ln(V_2^2/V_1^2)$ |
| skin depth | $\delta = \sqrt{2\rho/\mu_0\omega}$ |
Symbols: $\Phi$ flux (Wb) · $\varepsilon$ EMF (V) · $f$ frequency, $\omega = 2\pi f$ · $\rho$ resistivity (Ω·m), $\rho_m$ density (kg/m³) · $a$ the ring's mean radius, $a_{out}$ and $a_{in}$ its outer and inner radii, $t$ its wall, $h$ its height · $m$ its mass, $mg$ its weight · $V$ the supply voltage · $I_1$, $I_2$ coil and ring currents, $\hat{I}_1$, $\hat{I}_2$ their amplitudes · $L_1$, $L_2$ self-inductances, $M$ mutual inductance, $M′ = \partial M/\partial z$ · $R_1$, $R_2$ resistances · $B_r$ the radial field at the ring · $z$ the ring's height above the plate, $v$ its speed · $\theta$ the ring current's lag behind $I_1$, $\varphi = \theta - 90°$ its lag behind its own EMF · $\tau_1$, $\tau_2$ time constants · $k = 2\pi a B_r/I_1$ · $W_B$ magnetic energy, $K$ and $U_g$ kinetic and gravitational energy · $F_0$, $\ell$ the push's fitted value at the plate and its decay length · $\delta$ skin depth · $\mu_0$ = 4π × 10⁻⁷ H/m.
Further reading
P. J. H. Tjossem and E. C. Brost, "Optimizing Thomson's jumping ring," American Journal of Physics 79, 353–358 (2011), whose rings, resistivities and best-lag result the sim follows; OpenStax, University Physics Volume 2, chapter 13, "Electromagnetic Induction" (CC BY-NC-SA 4.0), for Faraday's and Lenz's laws and motional EMF. The Field Manual lists every source and every assumption of the model.
Jumping Ring Lab v1.5 · © 2026 Dr. David Meier · CC BY-NC-SA 4.0 · glidepathscience.org