Torque & Static Equilibrium · Guide · glidepathscience.org
GuideTorque & Static Equilibrium
Contents
This Guide covers the ideas and equations behind every Walkthrough step, Concept Challenge question and Predict round. Read Part 1 before the Intro track and Part 2 before the Advanced track, about ten minutes each. Every view in the lab is two-dimensional, so “clockwise” is read straight off the page.
Part 1 · The essentials
The big idea
A body with size can be pushed without moving anywhere and still start to turn. Whether it turns depends on where each force acts as much as on how big it is. A body is in static equilibrium only when the forces balance and their turning effects balance, and the turning effect of a force is its torque.
Torque and the lever arm
Pick an axis. A force F applied at a distance r from it, at an angle θ between the position vector and the force, has the torque
$τ = rF\sin θ = r_⊥F$
The lever arm $r_⊥ = r\sin θ$ is the perpendicular distance from the axis to the force’s line of action, the line the force lies along. A push straight toward the axis has $r_⊥ = 0$ and turns nothing, however hard it is. The same push at twice the distance gives twice the torque: that is why a door handle is far from the hinges.
Which way: the sign of a torque
Counterclockwise torques are positive, clockwise ones negative, seen face on as the lab draws them. In vector terms counterclockwise is +z, out of the page (⊙), and clockwise is −z (⊗). For a force with components $F_x$ and $F_y$ acting at (x, y) from the axis,
$τ_z = xF_y - yF_x$
“Down is clockwise” is a trap: a downward force left of the axis turns the body counterclockwise.
Two conditions, about any axis
A body in static equilibrium satisfies both
$ΣF = 0$ $Στ = 0$
When the forces balance, the net torque comes out the same about every point, so you may choose the axis. Choose it through an unknown force: its lever arm is zero and it drops out of the torque equation. Then $ΣF = 0$ gives what is left. A seesaw’s pivot pushes up with the whole weight of children and plank; where the children sit is set by the torques, $m_Ad_A = m_Bd_B$, and g cancels.
The center of gravity
The weight of every part of a body acts as if it were all at one point, the center of gravity:
$x_{cg} = Σm_ix_i/Σm_i$
A body balances on a support directly under its CG, and a body hung from a peg turns until its CG is directly below the peg. Hang it from two points and the two plumb lines cross at the CG. The CG need not be in the material: a ring’s is at its empty center, and an L-bracket’s is in the space inside the L.
Tipping
Tilt a box about one bottom edge. While its CG is over the base, the weight’s torque about that edge tips it back; once the CG passes beyond the edge, the same torque tips it over. With the CG a height h up and midway across a base w wide,
$\tan θ_{tip} = (w/2)/h$
A wider base or a lower CG means a larger tilt before it falls.
Struts, hinges and cables
A strut hinged to a wall and held by a cable has three unknowns: the cable’s tension and the hinge’s two components. Torques about the hinge remove both hinge components at once; then the two force equations give them. A heavy strut’s hinge force is not along the strut: its own weight acts between the two ends, so the hinge must push up as well as out.
Levers in the body
Muscles attach close to the joints they turn, so their lever arms are short and they pull many times the load. In a first-class lever the fulcrum is between the effort and the load (the head on the neck); in a second-class lever the load is in the middle (a heel raise); in a third-class lever the effort is in the middle (the forearm). A short lever arm trades force for speed: the hand moves far for a small shortening of the biceps.
Ladders
A smooth wall can only push straight out from its surface, horizontally, and that push shoves the top away from the wall. Only the floor’s static friction, pointing toward the wall, keeps the foot from sliding out, so the floor’s friction equals the wall’s push. Taking torques about the foot, with the ladder’s weight at its middle and a climber d up a ladder of length L at angle θ,
$f = N_{wall} = (m/2 + Md/L)g/\tan θ$ $f_s ≤ μ_sN$
The higher the climber, or the shallower the ladder, the more friction it takes. The floor’s normal force is the total weight.
Part 2 · Going further
Torque as a cross product, and couples
In full, $\vec{τ} = \vec{r} × \vec{F}$, perpendicular to both; in the plane only its z part survives. Moving the axis from P to P′ changes the torque by
$τ_{P′} = τ_P + (\vec{r}_P - \vec{r}_{P′}) × Σ\vec{F}$
so the net torque is the same about every point exactly when $ΣF = 0$. A couple, two equal and opposite forces a distance d apart, has ΣF = 0 and the torque Fd about every point: it turns without pushing.
The center of gravity by integration
For a rod whose mass per length λ varies along it, the sums become integrals:
$x_{cg} = ∫xλ\,dx/∫λ\,dx$
The CG equals the center of mass only in uniform gravity. A very tall tower’s lower parts feel slightly stronger gravity, so its CG sits a little below its center of mass.
Three forces meet at a point
If exactly three forces hold a body in equilibrium and they are not parallel, their lines of action meet at one point: about the crossing of two of them, the third must have zero torque too. A light member loaded only at two pins is a two-force member, and its force runs straight along it.
Friction at both ends, and indeterminacy
With friction at the wall too, the ladder has four unknown contact forces and only three equations: it is statically indeterminate. The wall’s friction can take any value in a band that keeps both frictions within μN, and how the ladder was set in place decides which. At impending slip both ends slide at once, the band shrinks to one value, and a uniform ladder alone stands down to
$\tan θ_{min} = (1 - μ_wμ_f)/(2μ_f)$
What flexes decides
A plank on three supports is indeterminate too. Rigid statics allows the middle support anything from nothing to the whole weight; stiffness picks the value. Model the plank as an elastic beam (bending stiffness EI) on springs (stiffness k), and compare them with κ = kl³/EI, where l is a span. For two equal spans under the plank’s own weight,
$R_{mid}/W = (24 + 5κ)/(72 + 8κ)$
A rigid plank on soft springs (κ → 0) squeezes them equally, W/3 each; a flexible plank on rigid supports (κ → ∞) sags onto the middle one.
Tip or slide, and the energy to tip
Push a box horizontally at height h. It tips when $F = mg(w/2)/h$ and slides when $F = μ_smg$, so it tips first when
$h > w/(2μ_s)$
whatever its mass. As the push grows, the floor’s push moves forward by Fh/mg, and it reaches the front edge exactly at the tipping point. Standing is stable because tipping needs energy: the CG must rise over the edge,
$ΔU = mg(\sqrt{h^2 + (w/2)^2} - h)$
A crane’s counterweight
A crane on outriggers tips forward about the front outrigger when loaded, and backward about the rear one when empty with its boom raised. The counterweight must be large enough for the first and small enough for the second: a band of safe values, which can be empty for a heavy load far out.
The hip and a cane
Standing on one leg, the body’s weight acts well to the side of the stance hip and the hip abductors pull on a short lever arm on the other side, so they pull more than the body weight and the hip carries over twice it. A cane in the opposite hand pushes up far from the hip, on the body’s side, and relieves the abductors; in the same hand it adds torque instead.
Balance in flight, and where statics ends
An airplane’s CG is usually ahead of the wing’s lift. In level flight the tail must push down to balance it: about the lift, $Wd = F_tl$, so the wing lifts $W + F_t$ and the stall speed rises by $\sqrt{1 + d/l} - 1$. A forward CG costs speed; an aft one reduces stability. On the ground, moving a mass m by Δd moves the CG by
$Δx_{cg} = mΔd/M$
Rigid statics stops where bodies bend, where several muscles pull at once, and where masses move, as fuel does in flight. The choice of axis is never one of its limits.
Reference
Common mistakes
- Multiplying force by distance without the sine: only the part of the force across the line to the axis turns.
- “Down is clockwise”: the side of the axis decides the sense.
- Thinking the answer depends on the axis: in equilibrium every axis gives the same forces.
- Putting a plank’s weight at its end, or forgetting it: it acts at the CG.
- Assuming the CG must be inside the material.
- Pointing a heavy strut’s hinge force along the strut.
- Forgetting the floor’s friction on a ladder, or drawing the wall’s push vertical.
- Taking a muscle’s pull as the load: its short lever arm makes it many times larger.
- Treating μN as the friction, when it is only the most friction can be.
Equation sheet
| Intro | |
|---|---|
| torque | $τ = rF\sin θ = r_⊥F$ |
| equilibrium | $ΣF = 0$ and $Στ = 0$ |
| center of gravity | $x_{cg} = Σm_ix_i/Σm_i$ |
| tipping | $\tan θ_{tip} = (w/2)/h$ |
| static friction | $f_s ≤ μ_sN$ |
| Advanced | |
|---|---|
| cross product | $\vec{τ} = \vec{r} × \vec{F}$: $τ_z = xF_y - yF_x$ |
| moving the axis | $τ_{P′} = τ_P + (\vec{r}_P - \vec{r}_{P′}) × Σ\vec{F}$ |
| CG by integration | $x_{cg} = ∫xλ\,dx/∫λ\,dx$ |
| ladder at slip | $\tan θ_{min} = (1 - μ_wμ_f)/(2μ_f)$ |
| tip or slide | tips first when $h > w/(2μ_s)$ |
| energy to tip | $ΔU = mg(\sqrt{h^2 + (w/2)^2} - h)$ |
| weight shift | $Δx_{cg} = mΔd/M$ |
τ torque (N·m); r distance from the axis; $r_⊥$ lever arm; θ angle between r and F; $x_{cg}$ center of gravity; w base width; h height of the CG (or of a push); $μ_s$, $μ_f$, $μ_w$ static coefficients (floor, wall); N normal force; λ mass per length; m, M masses; d, Δd distances; κ = kl³/EI.
Further reading
OpenStax, University Physics Volume 1, §10.6 Torque and §12.1–12.2 Static Equilibrium, which the Walkthrough follows; OpenStax, College Physics 2e, §9.3 Stability and §9.6 Forces and Torques in Muscles and Joints. The FAA Aircraft Weight and Balance Handbook (FAA-H-8083-1B) for datum, arm, moment and CG limits. The Field Manual lists the model and its limits.
Torque & Static Equilibrium v1.2 · © 2026 Dr. David Meier · CC BY-NC-SA 4.0 · glidepathscience.org