Springs & Elastic Potential Energy · Guide · glidepathscience.org
GuideSprings & Elastic Potential Energy
Contents
This Guide explains the ideas and equations behind every Walkthrough step, Concept Challenge question and Predict round, in the order a textbook would take them. Part 1 prepares the Intro track and Part 2 the Advanced track; each takes about fifteen minutes to read. Each section ends with a worked example that is not one of the sim's own problems.
Part 1 · The essentials
Hooke’s law: the pull grows with the stretch
Springs are everywhere: in mattresses, car suspensions, kitchen scales and the bonds that hold molecules together. What makes them useful is that their force is predictable. Pull the end of a spring and it pulls back; pull twice as far and, over a wide range, it pulls back twice as hard.
Measure the end's position from where it sits when the spring is relaxed, at its rest length, and call that displacement the stretch x, positive when the spring is longer and negative when it is squeezed shorter. Hooke’s law gives the force the spring exerts on whatever holds its end:
$F = -kx$
The spring constant k, in newtons per meter, measures stiffness. The minus sign carries the direction: x and F always have opposite signs, so the force points back toward the rest length. Stretched, the spring pulls its end back in; squeezed, it pushes it back out; at the rest length it exerts no force. A force like this is called a restoring force. Graphs usually show the size of the pull you apply instead, $F = kx$: a straight line through the origin whose slope is the spring constant, $k = F/x$.
The simplest way to measure k is to hang a known mass m from the spring and let it come to rest. The net force is then zero, so the spring pulls up exactly as hard as gravity pulls down: $kx = mg$, and $k = mg/x$. The usual mistakes are in the units: the stretch must be in meters, and the force is the weight $mg$ in newtons, not the mass in kilograms.
A single spring is rarely the whole story, and the rules for combining springs follow from the same law.
Side by side, end to end, and cut in pieces
Suspensions and mattresses use many springs at once, and a single coil is itself many small springs joined together. Knowing how stiffnesses combine predicts how a whole set behaves.
Two springs side by side holding a level bar are in parallel. The bar makes both stretch by the same x, so their pulls, $k_1x$ and $k_2x$, add, and the pair acts like one spring of stiffness
$k = k_1 + k_2$
The stiffer spring carries more of the load, in proportion to its k.
Hung end to end, in series, the springs behave differently. Follow the force down the chain: the lower spring holds the load, so it pulls with the whole load F, and the upper spring holds the lower one and the load, so it pulls with F too (the springs' own weight is neglected; a later section adds it). Each stretches by its own $F/k_i$, the stretches add, and
$1/k = 1/k_1 + 1/k_2$
The pair is softer than either spring. The common mistake is to split the load between springs in series; sharing the load is what parallel springs do.
A coil is a chain of identical turns in series. Each turn carries the whole load and adds its own small stretch, so half as many turns stretch half as much: the spring is twice as stiff. Cut a spring of stiffness k into n equal pieces, and each has
$k_{piece} = nk$
Stretching a spring takes work, and the spring stores it.
Elastic energy is the area under F(x)
A drawn bow and the squeezed spring of a pinball launcher hold energy that can be released later. That stored energy is elastic potential energy, and for a spring it can be read straight off a graph.
Pull the end slowly from the rest length to a stretch x, so that the hand's pull always just balances the spring and all of its work goes into the spring. The pull is not constant, so the work is not force times distance: it is the area under the graph of pull against stretch, a triangle of base x and height kx.
$U = \frac{1}{2}kx^2$
The energy U is in joules when k is in newtons per meter and x in meters, and it is the same for a stretch or a squeeze. Because U grows as the square of x, twice the stretch stores four times the energy: the triangle doubles in base and in height, and the second half of the stretch costs three times the work of the first. The usual slips are losing the ½, which treats the area as a rectangle, and writing the force kx where the energy belongs. Released, a squeezed spring hands its energy to what it pushes: a block on a frictionless track leaves with $\frac{1}{2}mv^2 = \frac{1}{2}kx^2$.
Gravity adds a twist when the spring hangs, and with it one of this topic's surprises.
Hanging a mass, and the missing half
A hanging spring is the working part of a spring scale, and it holds a puzzle about energy that appears again when a battery charges a capacitor.
A mass m hanging at rest is not on a relaxed spring. The net force is zero, so the spring pulls up with exactly $mg$, and that takes a stretch
$x = mg/k$
The ceiling holds the spring and the spring holds the mass, passing the whole weight up to its support.
Now follow the energy. Lower the mass by hand from the unstretched length to the balance point $d = mg/k$. Gravity gives up $mgd$, but the spring stores only $\frac{1}{2}kd^2 = \frac{1}{2}mgd$: exactly half. The hand took the other half, since it pushed up on the mass while the mass moved down. Let go at the unstretched length instead, and nothing takes that half. The mass overshoots and stops for an instant only where all that gravity gave up is in the spring, $mgy = \frac{1}{2}ky^2$:
$y = 2mg/k$
Without friction it swings between the two points forever; with a little friction it settles at d, and the missing half becomes heat. (Exactly half needs a linear spring and a start from the unstretched length.) A battery charging an empty capacitor through a resistor splits its energy the same way. Taking $mg/k$, the resting point, for the lowest point of a mass let go is the slip to avoid.
A graph of potential energy makes balance points easy to see, for any force that depends only on position.
Valleys and hilltops: reading a potential-energy curve
A bead between springs, the atoms of a molecule and a roller-coaster car are all easier to understand from a graph of potential energy than from their forces. The graph shows where a system can rest, where it moves fastest and where it turns around.
For a force that depends only on position along a line, the force is minus the slope of the curve:
$F = -\dfrac{dU}{dx}$
The force points downhill on the graph, toward lower potential energy, and where the curve is flat it is zero: those places are the equilibria. In a valley a nudge either way meets a force pushing back, so the equilibrium is stable; on a hilltop the force after a nudge points away, so it is unstable, like a pencil on its point; a flat stretch is neutral. Zero net force makes an equilibrium; the shape of the curve decides its stability.
Energy conservation does the rest. Without friction, E = K + U stays constant, so the kinetic energy is K = E − U, and since K cannot be negative the system can only be where U ≤ E. It moves fastest where U is lowest and stops for an instant where $U = E$, its turning points. The common mistake is to read the steepest part of the curve as the fastest: steepness gives the force, and so the acceleration, not the speed.
Every spring so far has been ideal. Real springs obey Hooke's law only over part of their range.
Real springs
Laboratory springs depart from Hooke's law in three ways that are easy to recognize on a graph of pull against stretch.
Many extension springs are closed-wound: their coils press on each other with a force $F_\mathrm{i}$, the pre-tension, so the spring does not stretch until the pull passes $F_\mathrm{i}$, and above that $F = F_\mathrm{i} + kx$. The line meets x = 0 at $F_\mathrm{i}$, and a straight-line fit gives k from its slope and $F_\mathrm{i}$ from its intercept, once the points taken while the coils were shut are left out. (A sensor that was not zeroed also shifts every reading, but then the trace slopes from the start; a shut spring's trace climbs straight up at x = 0.)
Rubber and many other materials have internal friction, so loading and unloading follow different curves and less work comes back than went in. The area between them, the hysteresis loop, is the heat made in each cycle; it is why a rubber band worked back and forth warms up. And a spring stretched past its elastic limit stretches for good: let back, it reaches zero pull at a longer length, a permanent set.
Part 2 returns to these ideas with more tools: the shape of a curve near its bottom, springs pulled sideways, and the energy books of real materials.
Part 2 · Going further
Every valley is a spring
Springs matter far beyond springs because of this result: near the bottom of any smooth valley, a system behaves like a mass on a spring. That is why a bond, a pendulum and a marble in a bowl all oscillate alike when the motion is small.
Expand U(x) in a Taylor series about a minimum at $x_0$. The slope is zero there, so the first-derivative term vanishes:
$U(x) \approx U(x_0) + \frac{1}{2}U″(x_0)(x - x_0)^2$
That is the energy of a spring of stiffness
$k = U″(x_0)$
The constant $U(x_0)$ changes nothing, since only differences in potential energy matter; the curvature sets the stiffness, so a deep but wide well can be soft. Its sign settles stability, positive in a valley and negative on a hilltop, and where $U″ = 0$ the next term decides.
A hanging spring shows the idea at work. Measured down from the unstretched end, $U = \frac{1}{2}ky^2 - mgy$, the spring's parabola plus gravity's straight line. Its slope is zero at $y_0 = mg/k$, the balance found before from forces, and completing the square gives $U = \frac{1}{2}k(y - y_0)^2 - \frac{1}{2}ky_0^2$: the same parabola, moved. A straight line never changes a curvature, so $U″$ is still k, and a hanging spring behaves about its balance point as a horizontal one does about its rest length. It is not stiffer for hanging, and its balance is not where U = 0.
Curvature tells how stiff a combination is, not which spring in it holds the energy.
Which spring stores the energy
In a set of springs the energy is not shared evenly, and a designer who wants one part to take the strain needs to know which.
End to end, every spring carries the same force F and stretches $F/k_i$, so its energy $\frac{1}{2}k_ix_i^2$ is
$U_i = F^2/2k_i$ $U_1/U_2 = k_2/k_1$
In series the softer spring stretches more and stores more. Side by side it is the other way around: the springs share one stretch, each stores $\frac{1}{2}k_ix^2$, and the stiffer one stores more. The tempting slip is $k_1/k_2$, which gets the series case backward.
Springs can also push and pull across a direction they do not lie along.
A bead pulled sideways: tension, flat wells and double wells
A guitar string resists a pluck because it is under tension, not because it bends. The same physics, built on a table, gives three kinds of well from one setup.
Put a bead between two identical springs of stiffness k and rest length $L_0$, anchored a distance L to either side, and pull it a distance y sideways. Each spring has length $r = \sqrt{L^2 + y^2}$, and together they store
$U = k(\sqrt{L^2 + y^2} - L_0)^2$
If $L > L_0$, the springs are stretched even with the bead in the middle, each carrying a tension $T_0 = k(L - L_0)$. A small sideways move barely changes their length but tilts each by about y/L, and the sideways parts of the two tensions pull the bead back with $2T_0y/L$: a sideways stiffness
$k_y = 2T_0/L$ $T_0 = k(L - L_0)$
which is $U″(0)$. Tighten the springs and the bead gets stiffer sideways, as a tightened string's pitch rises. The common mistake is $2k$, the stiffness along the springs.
If $L = L_0$, the springs carry no tension at the middle. Then $r - L_0 \approx y^2/2L_0$, so $U \approx ky^4/4L_0^2$ and $F \approx -ky^3/L_0^2$. The middle is still stable, since U rises on both sides, but $U″ = 0$: small oscillations are not simple harmonic, and the smaller they are, the slower they come back. Zero curvature does not mean instability; the next term decides.
If $L < L_0$, the squeezed springs push the bead away from the middle, which has become a hilltop. The bead rests where each spring has its rest length, $\sqrt{L^2 + y^2} = L_0$:
$y^∗ = \pm\sqrt{L_0^2 - L^2}$ (when $L < L_0$)
Each valley is a spring of stiffness $2ky^{∗2}/L_0^2$. Two stable states with a hilltop between them make a snap-through switch, the way a light switch or a hair clip works. The usual slip is $L_0 - L$: the spring runs on a slant from the anchor to the bead, so Pythagoras applies.
Back to a single spring, and to the real-spring features of Part 1, now with their energy.
Pre-tension
Closed-wound springs close screen doors and return levers because their pre-tension keeps them shut until a definite pull opens them. Beyond that pull,
$F = F_\mathrm{i} + kx$ $U = F_\mathrm{i}x + \frac{1}{2}kx^2$
The energy is the area under the line: a rectangle of height $F_\mathrm{i}$, since the pull is at least $F_\mathrm{i}$ from the first millimeter, plus the familiar triangle. Leaving out the rectangle is the classic slip, and ½Fx, a triangle from zero, is another. Pre-tension is a force the shut coils already carry, so the line meets x = 0 at $F_\mathrm{i}$; an initial stretch only moves the zero of x, and a permanent set slides the whole line sideways.
Pre-tension still gives a straight line. Other springs bend away from Hooke's law altogether.
Stiffening and softening springs
Rubber bands, foam and tendons get stiffer, or softer, as they stretch. One extra term in Hooke's law captures both:
$F = kx + \beta x^3$ $U = \frac{1}{2}kx^2 + \frac{1}{4}\beta x^4$
With β > 0 the spring stiffens: its F(x) curve bends up away from the line of slope k, and at a large stretch the $x^4$ term dominates the energy. The cubic force integrates to $\frac{1}{4}\beta x^4$; the slips are $\frac{1}{2}\beta x^4$ and leaving the term out.
With β < 0 the spring softens, and its pull has a largest value: $dF/dx = 0$ at $x^∗ = \sqrt{k/3|\beta|}$, where $F_\mathrm{max} = \frac{2}{3}kx^∗$. A dead load heavier than that has no balance. The load tilts the well $U - Fx$, and as it grows toward $F_\mathrm{max}$ the valley and the hilltop beyond it move together, merge and vanish, so the load runs away. The cubic is a local model: a real spring would change, or break, first.
A nonlinear spring still gives back all its energy. Real materials do not.
Hysteresis and the elastic limit
Every real material turns some of the work done on it into heat, and the F(x) curve shows how much.
When loading and unloading follow different curves, the work put in on the way out, $W_{out}$, the area under the loading curve, is more than the work given back on the way in, $W_{back}$. The difference is the heat Q made in one cycle, the loop's area:
$Q = W_{out} - W_{back}$
This holds for a cycle that repeats, ending in the state where it began; the first loop from a fresh band also leaves some energy stored. The sim models the internal friction with an Iwan model, small springs each in series with a friction slider, which gives a smooth loop that is the same at any speed; real rubber also loses more when worked faster. The slips are to call all the work put in, or all that came back, the heat, and to confuse the fraction returned, $W_{back}/W_{out}$, with the fraction lost.
Past its elastic limit a spring yields. The sim treats it as elastic–perfectly plastic: the spring flows at a constant yield force $F_\mathrm{y}$, and its rest length grows (real spring steel work-hardens, so its pull keeps rising a little). It unloads along a line parallel to the elastic one and reaches zero pull at a permanent set p. The plastic work $F_\mathrm{y}p$ has become heat and does not come back.
So far every spring has been massless. A heavy spring carries its own weight, unevenly.
A spring’s own weight
A hanging Slinky's top turns spread wide while its bottom turns stay bunched. Its own weight is the reason.
In a uniform spring of mass $m_s$ holding a mass m, each turn holds up everything below it, so a fraction ξ of the way up the tension is $mg + m_sg\xi$, from $mg$ at the bottom to $(m + m_s)g$ at the top. Each piece stretches in proportion to its tension, so the total stretch is
$y = \frac{1}{k}\int_0^1 (mg + m_sg\xi)\,d\xi = (m + m_s/2)g/k$
On average the spring's weight counts half, as if half its mass hung at the end. Counting all of it, or a third, are the usual slips; $m_s/3$ belongs to a spring in motion, a topic for Simple Harmonic Motion & Pendulums. With pre-tension, the turns that carry less than $F_\mathrm{i}$ stay shut: hanging empty, the bottom fraction $F_\mathrm{i}/m_sg$ of the turns stays closed, the bunched bottom of a Slinky.
Every k in this Guide has been a given number. The last section asks where those numbers come from.
Where a spring constant comes from
A spring constant summarizes physics at a smaller scale, and three examples show how different that physics can be.
Two bonded atoms sit in a potential well, modeled well by the Morse potential, $U = D(1 - e^{-a(r - r_e)})^2$: its minimum is at the bond length $r_e$, and it levels off at the dissociation energy D as the atoms are pulled apart. Its curvature at the bottom is
$k = 2Da^2$
For hydrogen chloride that is about 516 N/m, like a stiff laboratory spring; the bond vibrates nearly 10¹⁴ times a second because the atoms are so light, not because k is unusual.
A coil spring's stiffness comes from twisting its wire. For a round wire of diameter d in n active turns of mean diameter D, with shear modulus G,
$k = Gd^4/(8D^3n)$
Double the wire's diameter and k grows sixteen times; more turns make a softer spring, the series rule again.
Rubber is different again. Stretching a band pulls its long, wriggling chain molecules into line and lowers their entropy, and their thermal motion pulls them back toward disorder. So the tension at a fixed stretch grows with temperature: a well-stretched band warmed with a hair dryer pulls harder, the opposite of a metal spring. (Stretched by less than about a tenth, ordinary thermal expansion wins, and a warmed band lengthens.)
Reference
Common mistakes
- The mass for the weight, or centimeters for meters. In $k = mg/x$, the force is $mg$ in newtons and x is in meters.
- Splitting the load between springs in series. End to end, each carries all of it.
- Thinking a shorter spring is softer. Half the turns give twice the k.
- Losing the ½ in the stored energy. Twice the stretch stores four times the energy.
- Mixing up the resting point and the lowest point. Lowered gently, a mass stops at $mg/k$ and the spring stores half of $mgd$; let go, it falls to $2mg/k$.
- Reading the steepest part of U(x) as the fastest. The speed is greatest where U is least.
- Calling an equilibrium with $U″ = 0$ unstable. A quartic well is stable.
- Getting the series energy ratio backward, or answering 2k for a sideways stiffness that comes from tension.
- Dropping a term: the rectangle $F_\mathrm{i}x$, the ¼ in ¼βx⁴, or a spring’s own weight, which counts half.
Equation sheet
| Part 1 | |
|---|---|
| Hooke’s law | $F = {-kx}$, $k = F/x$ |
| hanging at rest | $x = mg/k$ |
| side by side | $k = k_1 + k_2$ |
| end to end; cut | $1/k = 1/k_1 + 1/k_2$; $k_{piece} = nk$ |
| stored energy | $U = \frac{1}{2}kx^2$ |
| the missing half | lowered gently, the hand takes $\frac{1}{2}mgd$; let go, $y = 2mg/k$ |
| wells | $F = {-dU/dx}$; turning points where $U = E$ |
| Part 2 | |
|---|---|
| every valley | $k = U″(x_0)$ |
| energy in series | $U_i = F^2/2k_i$, $U_1/U_2 = k_2/k_1$ |
| side pull | $U = k(\sqrt{L^2 + y^2} - L_0)^2$ |
| sideways; valleys | $k_y = 2T_0/L$, $T_0 = k(L - L_0)$; $y^∗ = \pm\sqrt{L_0^2 - L^2}$ when $L < L_0$ |
| pre-tension | $F = F_\mathrm{i} + kx$, $U = F_\mathrm{i}x + \frac{1}{2}kx^2$ |
| nonlinear | $F = kx + \beta x^3$, $U = \frac{1}{2}kx^2 + \frac{1}{4}\beta x^4$ |
| loop | heat per cycle $= W_{out} - W_{back}$ |
| own weight | stretch $= (m + m_s/2)g/k$ |
| bonds; coils | $k = 2Da^2$; $k = Gd^4/(8D^3n)$ |
Symbols: x stretch from the rest length · k spring constant (N/m) · F force or pull (N) · U potential energy (J) · m mass, $m_s$ the spring’s own mass · g = 9.81 m/s² · d balance stretch, or a coil’s wire diameter · E total energy · L anchor distance, $L_0$ rest length, $T_0$ tension · $F_\mathrm{i}$ pre-tension · β cubic term (N/m³) · $F_\mathrm{y}$ yield force, p permanent set · D well depth (bonds) or coil diameter, a Morse width, G shear modulus, n turns.
Further reading
OpenStax, University Physics Volume 1, chapters 7 and 8 (work done by a spring, potential energy, and §8.4, potential-energy diagrams and stability) and chapter 12 (elasticity and plasticity); R. G. Budynas and J. K. Nisbett, Shigley’s Mechanical Engineering Design, for helical springs; L. R. G. Treloar, The Physics of Rubber Elasticity, for rubber. How fast a mass oscillates on a spring, and the $m_s/3$ correction, are in Simple Harmonic Motion & Pendulums. The Field Manual lists every source.
Springs & Elastic Potential Energy v1.6 · © 2026 Dr. David Meier · CC BY-NC-SA 4.0 · glidepathscience.org