Rotational Dynamics & Rolling · Guide · glidepathscience.org
GuideRotational Dynamics & Rolling
Contents
This Guide explains the ideas and equations behind every Walkthrough step, Concept Challenge question and Predict round, in the order a textbook would take them. Part 1 prepares the Intro track and Part 2 the Advanced track; each takes about eighteen minutes to read. Each section ends with a worked example that is not one of the sim’s own problems, so you can check your method against it and then try the sim’s versions. Throughout, counterclockwise seen from the front (+z, out of the page) counts as positive, and g = 9.81 m/s².
Part 1 · The essentials
Angles, radians and steady turning
A spinning wheel, a ceiling fan and a hard drive’s platter all move without going anywhere: every point travels in a circle while the body stays put. What does describe it is an angle: how far the body has turned. Rotational motion is the study of that angle and how it changes, and almost every idea from straight-line motion has a twin here once the angle is measured the right way.
The right way is in radians. An angle of one radian is the angle at the center of a circle that cuts off an arc exactly as long as the radius. In general, an arc of length s on a circle of radius r subtends
$\theta = s/r$
Because a full circle’s circumference is $2\pi r$, one revolution is $2\pi$ rad, about 6.28 rad, and one radian is about 57.3°. The radian is a ratio of two lengths, so it carries no real unit and slips cleanly into the formulas that link turning to motion along the rim; every rotational equation below assumes it.
The rate of turning is the angular velocity, and its rate of change is the angular acceleration. Over an interval Δt their averages are
$\bar{\omega} = \Delta\theta/\Delta t$ $\bar{\alpha} = \Delta\omega/\Delta t$
and at an instant they are the derivatives $\omega = d\theta/dt$ and $\alpha = d\omega/dt$; at a steady rate the two agree. ω is in radians per second and α in radians per second squared. Engines and turntables are rated in revolutions per minute (rpm); one rpm is $2\pi/60$ = 0.105 rad/s. When α is constant, the four kinematic equations of straight-line motion carry over with x, v and a renamed θ, ω and α, where θ is the angular displacement, the angle turned from the start:
$\omega = \omega_0 + \alpha t$ $\theta = \omega_0 t + \tfrac{1}{2}\alpha t^2$ $\omega^2 = \omega_0^2 + 2\alpha\theta$
The usual mistakes are the same as in one dimension, plus one: an angle left in degrees or revolutions. A wheel that turns 5 revolutions has turned $10\pi$ rad, not 5, and an equation fed the wrong unit gives a wrong answer without complaint.
A body turning at one ω is still moving very differently at different places on it, and that is the next idea.
One ω, many speeds
Every point of a rigid body turns through the same angle in the same time, so the whole body shares one ω and one α. What differs from point to point is how far each point travels while it turns. A point at distance r from the axis sweeps an arc $s = r\theta$, so its speed along its circle and its acceleration along that circle are
$v = r\omega$ $a_t = r\alpha$
A child on the rim of a merry-go-round therefore moves faster than one near the middle, though both turn together.
A point moving in a circle also accelerates toward the center even when ω is steady, because its velocity keeps changing direction. That centripetal acceleration is
$a_c = r\omega^2$
which is the familiar $v^2/r$ written with ω. A point on a turning body that is also speeding up has both: $a_t$ along the rim and $a_c$ toward the axis, at right angles, so the total is $\sqrt{a_t^2 + a_c^2}$. Two slips are common here: writing $a_c = r\omega$ (which is the speed, not an acceleration) and writing $\omega^2/r$ (which mixes the two forms). A quick check on units catches both: $r\omega^2$ is in m/s².
The speeds and accelerations follow from ω and α. What sets α in the first place depends on how the body’s mass is arranged.
Moment of inertia: where the mass is
In straight-line motion, mass measures how hard a body is to speed up. In rotation the same role is played by the moment of inertia, and it depends on more than the mass: it depends on how far each bit of mass is from the axis. For a body made of small masses m at distances r from the axis,
$I = \sum mr^2$
The square is the key. Each bit of mass moves at $v = r\omega$, so its kinetic energy is $\tfrac{1}{2}m(r\omega)^2$, and a bit twice as far out counts four times as much. A hoop and a disk of the same mass and radius are a striking pair: in the hoop every bit of mass is at the rim, $I = MR^2$, while the disk’s mass is spread inward, and the sum over it gives $I = \tfrac{1}{2}MR^2$. Given the same torque on frictionless axles, the disk spins up twice as fast.
Because I depends on distances from the axis, the same body has a different I about every axis. Two equal masses on the ends of a light rod have twice the moment of inertia about one end that they have about the center, and a uniform rod has four times as much, although nothing about the rod has changed. A statement of I always comes with its axis. It does not depend on how fast the body turns, nor on anything but the masses and their distances.
For round bodies it is convenient to write $I = \beta MR^2$, where the pure number β depends only on the shape: 1 for a hoop, ½ for a disk or solid cylinder, ⅖ for a solid sphere and ⅔ for a thin spherical shell. The common mistake is to treat I as the mass, or to forget that the same body has a new I about a new axis.
With I in hand, we can say exactly how a torque spins a body up.
Torque makes angular acceleration
A force makes a body turn only if it has a lever arm about the axis. The torque of a force F applied at distance r from the axis, at an angle φ between the radius and the force, is
$\tau = rF\sin\varphi$
A push straight toward the axis has no torque; a push at right angles to the radius has the most. A string wound on a wheel’s rim pulls along the tangent, so its torque is simply rF. Torque & Static Equilibrium treats the lever arm in full; here what matters is what a net torque does. Newton’s second law for rotation says
$\tau_{net} = I\alpha$
the exact twin of $F_{net} = ma$. Doubling the torque doubles α; doubling I halves it. Note what is not in it: a body’s mass alone. Writing α = F/m for a turning body is a common slip, and so is using the hoop’s $MR^2$ for a disk.
A pulley that has mass is where this law meets Newton’s second law for the masses hanging from it. If the string does not slip, the pulley’s rim moves with the string, so $a = R\alpha$. The pulley can only speed up if a net torque acts on it, so the tensions on its two sides must differ: $(T_2 - T_1)R = I\alpha$. Combining that with $m_2 g - T_2 = m_2 a$ and $T_1 - m_1 g = m_1 a$ gives
$a = (m_2 - m_1)g/(m_1 + m_2 + I/R^2)$
The pulley acts as an extra mass $I/R^2$ that has to be accelerated but that gravity does not pull: ½M for a uniform disk, M for a thin ring. The usual mistakes are to make the tensions equal, which would leave the pulley with no torque to speed it up, or to count the pulley’s whole mass.
Torques that act through an angle do work, and the energy they deliver is stored in the spin.
Work and energy in spin
A torque that turns a body through an angle does work on it, just as a force does along a distance. The work is the integral of the torque over the angle, which for a steady torque is the torque times the angle turned:
$W = \int \tau\,d\theta$ $W = \tau\Delta\theta$
with θ in radians, which is the reason the radian is used everywhere. That work goes into the energy of the turning, the rotational kinetic energy, which is the sum of $\tfrac{1}{2}mv^2$ over every bit of the body with $v = r\omega$:
$K_R = \tfrac{1}{2}I\omega^2$
The rotational work-energy theorem, the net torque’s work equals $\Delta K_R$ ($\tau\Delta\theta = \Delta K_R$ for a steady net torque), is the twin of $F\Delta x = \Delta K$. The rate at which a torque does work is the power, $P = \tau\omega$, which is why a motor rated for a given power can give a large torque only at low speed. Two slips are common: putting the angle in revolutions (W comes out $2\pi$ times too small) and losing the ½ in $K_R$.
A body that moves and spins at once carries both kinds of kinetic energy. A cylinder rolling along at speed v also turns at ω = v/R, so its total is $K = \tfrac{1}{2}mv^2 + \tfrac{1}{2}I\omega^2$. Writing $I = \beta mR^2$, the spin’s share is $\tfrac{1}{2}\beta mv^2$: the radius cancels, and the fraction of the energy in spin is $\beta/(1 + \beta)$, a third for a solid cylinder and half for a hoop, whatever their size.
That share of energy in spin is the whole story of rolling, which comes next.
Rolling, and the race
A wheel that rolls without slipping both moves and turns, and the two are locked together: in one turn the wheel advances one circumference, $2\pi R$, so the center’s speed and the turning rate obey
$v_{CM} = R\omega$
Each point of the rim moves with the center’s velocity plus its own turning velocity, $\vec\omega \times \vec r$, which has size $R\omega = v_{CM}$ and points along the rim. At the top the two add, so the top of the wheel moves at $2v_{CM}$; at the bottom they cancel, and the point touching the ground is at rest for an instant. The bottom of a car’s tire is not moving relative to the road, so in the ideal model a rolling tire grips without sliding at all. A painted spot on the rim traces a cycloid, with a sharp cusp each time it touches the ground.
Because the contact point does not slide, friction there does no work, and a body rolling down a slope keeps its energy: $mgh = \tfrac{1}{2}mv^2 + \tfrac{1}{2}I\omega^2 = \tfrac{1}{2}mv^2(1 + \beta)$. So the speed after a drop h from rest is
$v = \sqrt{2gh/(1 + \beta)}$
and the acceleration down a slope at angle θ is
$a = g\sin\theta/(1 + \beta)$, $\beta = I_{CM}/(mR^2)$
Neither the mass nor the radius appears. That settles the classic race: released together from rest on one ramp and rolling without slipping, a solid sphere (β = ⅖) beats a solid cylinder (½), which beats a hollow sphere (⅔), which beats a hoop (1), whatever their masses and sizes, and any two bodies of one shape tie. The more of its mass a body carries far from its center, the more of its energy goes into spin and the less into moving. A block sliding without friction would beat them all, since it stores nothing in spin, and racers that all slip on one surface tie (Part 2). The mistake to avoid is $\sqrt{2gh}$ for a rolling body, which forgets the spin.
Part 2 takes the same ideas further: rotation as a vector, moments of inertia calculated and measured, and what happens when grip runs out.
Part 2 · Going further
Rotation as a vector
A turning sense, counterclockwise or clockwise, depends on where you look from, so a careful description gives rotation a direction in space instead. By the curl rule (the right-hand rule), curl the fingers of your right hand the way the body turns, and your thumb points along the angular velocity $\vec\omega$, along the axis. A wheel turning counterclockwise as seen from in front has $\vec\omega$ pointing out of the page, toward you, along +z; drawn on the page that is ⊙. The Right-Hand Rule Trainer drills this rule.
The angular acceleration is the rate of change of that vector, $\vec\alpha = d\vec\omega/dt$, and the torque $\vec\tau = \vec r \times \vec F$ lies along the axis too, with $\vec\tau_{net} = I\vec\alpha$ for a body turning about a fixed axis. For a body speeding up, $\vec\alpha$ points along $\vec\omega$; for a body slowing down, against it, exactly as a and v do in one dimension. The common mistake is to point α along the turning sense whatever the change, or along the rim, where the tangential acceleration $a_t$ is an ordinary vector in the plane.
The torque’s effect depends on I, and for real bodies I has to be calculated, or measured.
Calculating moments of inertia
For a continuous body the sum becomes an integral over its mass:
$I = \int r^2\,dm$
For a uniform rod of mass M and length L about its center, a slice of length dx at distance x holds $dm = (M/L)\,dx$, and $\int_{-L/2}^{L/2} x^2 (M/L)\,dx = \tfrac{1}{12}ML^2$. The same integral from 0 to L gives ⅓ML² about an end. A disk is a set of concentric rings, $dm = (2M/R^2)\,r\,dr$, giving ½MR², and a sphere a stack of thin disks, giving ⅖MR².
The integral rarely needs repeating, thanks to the parallel-axis theorem: the moment of inertia about any axis is the moment about a parallel axis through the center of mass plus the whole mass at the distance d between them,
$I = I_{CM} + Md^2$
The rod checks it: $\tfrac{1}{12}ML^2 + M(L/2)^2 = \tfrac{1}{3}ML^2$. Two consequences follow. I is least about the axis through the center of mass, and d must be measured from the center of mass, not from an end, which is the usual slip. Real round bodies sit between the ideal shapes. A thick-walled ring or pipe of inner radius $r_i$ and outer radius R has $I = \tfrac{1}{2}M(R^2 + r_i^2)$, so
$\beta = \tfrac{1}{2}(1 + (r_i/R)^2)$
which runs from ½ for a solid cylinder to 1 for a thin hoop. A thick spherical shell has $\beta = \tfrac{2}{5}(1 - k^5)/(1 - k^3)$ with $k = r_i/R$, from ⅖ to ⅔.
Shapes and formulas give I for ideal bodies. For a real wheel, I is measured.
Measuring a moment of inertia
The classic method hangs a mass m from a string wound on the wheel’s hub of radius r, lets it fall from rest, and times it. Over a drop d in time t, the acceleration is $a = 2d/t^2$. The mass obeys $mg - T = ma$, the wheel $Tr = I\alpha$, and the string ties them together with $a = \alpha r$. Eliminating the tension,
$I = mr^2(g/a - 1)$
The −1 matters: the tension is less than mg, because the mass is accelerating. Taking T = mg adds the falling mass’s own $mr^2$ to I, which reads I too high by $mr^2/I$: only 0.3 % with 50 g on the 2.5 cm hub of the sim’s heavy turntable, but 2 % in the light wheel of the example below. Losing the ½ in $d = \tfrac{1}{2}at^2$ is the other common slip.
One run also cannot tell the wheel’s I from the friction in its bearing, which drags on it with a torque $\tau_f$ of its own. The way out is to run several masses and plot the string’s torque, $\tau = mr(g - a)$, against the measured α. Since $\tau - \tau_f = I\alpha$, the points lie on a straight line whose slope is I and whose intercept is the friction torque. A run of the empty apparatus first gives the spindle’s own I, which is subtracted at the end.
A body rolling on a surface turns about a moving point. Choosing that point well makes rolling problems short.
Torques about the contact point, and the spool
For a rolling body the most convenient point to take torques about is often the contact point P. Friction and the normal force both act there and drop out, leaving only gravity and any pull. For a round, balanced body on a flat surface,
$\tau_P = I_P\alpha$ $I_P = I_{CM} + mR^2$
Down a slope this gives $mgR\sin\theta = (I_{CM} + mR^2)\alpha$ in one line, and with $a = R\alpha$ the familiar $a = g\sin\theta/(1 + \beta)$. The same result comes without the shortcut: Newton’s second law for the center, $ma = mg\sin\theta - f$, and the torque about the center, $fR = I_{CM}\alpha$, add (with $a = R\alpha$) to $(I_{CM} + mR^2)\alpha = mgR\sin\theta$, and friction drops out. Why the shortcut works takes care, because “the contact point” can mean two different things. The painted point of the tread that touches the ground is at rest for an instant, yet it is accelerating, toward the center at $v^2/R$. The place where contact happens is different: it slides along the ground with the center, at $v_{CM}$, and on a steady roll it does not accelerate. The shortcut takes torques about that moving place. About a moving origin, with L built from each part’s velocity relative to the ground, $\tau = dL/dt$ gains a term proportional to $\vec v_{\rm origin} \times m\vec v_{CM}$, and it is zero here because the contact place moves parallel to the center. That needs a round roller with its center of mass at its center, on a flat surface; the shortcut fails for a body that is not round, or whose mass is off center. The energy reads $K = \tfrac{1}{2}I_P\omega^2$: instant by instant, rolling is a pure rotation about the tread point that is touching the ground.
The spool shows the method’s power. A spool’s thread comes off the bottom of its hub, of radius r, on rims of radius R, and is pulled at angle φ above the table. About the contact point only the thread’s pull has a torque, and its sign depends on which side of P the thread’s line passes. Pulled low, the line passes above P and the spool rolls toward the pull, winding up thread; pulled steeply, it passes on the other side and the spool rolls away. At the critical angle the line passes through P, where the thread’s line, tangent to the hub, makes a right triangle with the hub’s radius r and hypotenuse R:
$\cos\varphi_c = r/R$
All of this assumed the body rolls. Rolling needs grip, and grip is limited.
The grip limit, and slipping
Gravity acts at the center of a rolling body and has no torque about it; the spin comes from friction at the contact. Rolling down a slope needs a static friction up the slope of $f = \beta mg\sin\theta/(1 + \beta)$, and static friction can supply at most $\mu_s N = \mu_s mg\cos\theta$. Setting them equal gives the steepest slope a body can roll down:
$\tan\theta_{max} = \mu_s(1 + \beta)/\beta$
For a solid cylinder that is $3\mu_s$, three times the tangent at which a block on the same surface slips: a roller needs only part of the friction a block would. Using $\tan\theta = \mu_s$ is the classic slip. A hoop, with its large β, needs the most grip and is the first to slip.
Past the limit the body slides at the contact, and kinetic friction $\mu_k N$ acts against the slip. The center and the spin then each have their own constant acceleration:
$a = g(\sin\theta - \mu_k\cos\theta)$, $\alpha = \mu_k mgR\cos\theta/I$
Since $R\alpha$ falls short of a, the slip speed $v - R\omega$ grows, and the heat it makes, friction times the slip distance, grows with it. Writing α = a/R is the mistake to avoid. The center’s acceleration has no β, so a hoop and a cylinder slipping on one surface tie, and a slipping body beats the same body rolling on a grippier one, which puts more energy into spin.
On level ground a body can still slip, if it starts with the wrong spin.
Skids, the fixed loss, and backspin
A bowling ball leaves the hand sliding, with little spin. At first its contact point slides forward over the lane, so kinetic friction acts backward: it slows the center at $\mu_k g$ and, through its torque about the center, spins the ball up at $\alpha = \mu_k mgR/I$. The skid ends when the two meet, $v = R\omega$, and from then on the ball rolls. For a body thrown at $v_0$ with a spin $\omega_0$, counted positive as backspin, the speed when it starts rolling and the time the skid lasts are
$v_f = (v_0 - \beta R\omega_0)/(1 + \beta)$, $t = |v_0 - v_f|/(\mu_k g)$
with $\omega_0$ = 0 here, giving $v_0/(1 + \beta)$: 5/7 of the throw for a solid sphere. The friction coefficient sets how long the skid lasts but not where it ends, because friction acts at the contact line and has no torque about it, so angular momentum about that line stays fixed through the skid. Angular Momentum & Gyroscopes develops that view.
The energy lost is also fixed. The final kinetic energy is $\tfrac{1}{2}mv_f^2(1 + \beta)$, which for a start with no spin is $1/(1 + \beta)$ of the start, so a skid always costs $\beta/(1 + \beta)$ of the energy, 2/7 for a sphere, whatever the lane. On an oiled lane the ball skids five times as far against a fifth of the friction, and the heat comes out the same. Expecting more loss on the longer skid is the common mistake.
The formula also covers backspin, with $\omega_0$ counted positive when the ball spins against its motion. If $\beta R\omega_0 > v_0$, the final velocity is negative: the body comes back. For a hoop (β = 1) that happens when its rim speed exceeds its forward speed. (The Sandbox counts spin as a roll rate, so there backspin is negative.)
Spin stores energy, and some machines exist to store it.
Power and flywheels
A flywheel stores energy in its spin, $K_R = \tfrac{1}{2}I\omega^2$, and because ω enters squared, a fast, heavy rim stores a great deal. A torque’s power is
$P = \tau\omega$
so a motor at constant power gives less torque the faster the wheel turns, $\tau = P/\omega$. From rest the formula promises an infinite torque; a real motor has a torque limit, and runs at that limit until it reaches the speed where the limit times ω equals its power. With no losses, the time to spin up at constant power is simply $t = K_R/P$. The slips to avoid are an rpm figure used as rad/s, which makes $K_R$ about 91 times too large, revolutions per second used as rad/s, which makes it about 39 times too small, and a hoop’s I for a disk.
Every idea so far treated bodies and floors as perfectly rigid. Real ones are not.
Where rigid rolling ends
In the rigid model a ball rolling on level ground rolls forever: it needs no friction at all, and the contact point, at rest, could do no work if friction were there. Real balls stop. The main reason is rolling resistance: the ball and the floor both deform a little, so the contact is a small patch rather than a point, and the floor pushes harder on its front half than its back. The normal force then acts slightly ahead of the center, and its torque opposes the roll. Air drag slows fast balls and flywheels. A tire never rolls with exactly zero slip either: it drives and brakes through a small slip in its contact patch, and its grip rises with that slip to a peak before falling off, the basis of traction control and anti-lock brakes. The rigid model is the right first approximation: these effects are small for hard bodies on hard surfaces.
One claim that sounds like one of these effects is false: static friction does not act backward on a ball rolling steadily on level ground, and it does no negative work there.
Reference
Ten common mistakes
- Degrees or revolutions in a radian formula. $s = r\theta$, $v = r\omega$, $W = \tau\Delta\theta$ and $K_R = \tfrac{1}{2}I\omega^2$ all need radians.
- One speed for the whole body. Every point shares ω; its speed is $r\omega$.
- I as the mass. I depends on where the mass is: a hoop’s is twice a disk’s of the same mass and radius.
- The axis forgotten. The same body has a different I about every axis, least through its center of mass.
- T = mg for a falling mass. An accelerating mass has $T = m(g - a)$.
- Equal tensions over a heavy pulley. They differ by $(I/R^2)a$, or the pulley could not speed up.
- The top of a rolling tire at v. It moves at 2v; the bottom is at rest.
- The heaviest racer wins. For racers rolling without slipping, mass and size cancel; only β decides.
- Spin forgotten in $mgh = \tfrac{1}{2}mv^2$. A roller keeps a share $\beta/(1 + \beta)$ of its energy in spin.
- More friction, more loss in a skid. A skid from no spin loses $\beta/(1 + \beta)$ of its energy whatever $\mu_k$.
The equation sheet
| Angles | $\theta = s/r$; $\bar{\omega} = \Delta\theta/\Delta t$; $\omega = d\theta/dt$; $\alpha = d\omega/dt$ |
|---|---|
| Constant α | $\omega = \omega_0 + \alpha t$; $\theta = \omega_0 t + \tfrac{1}{2}\alpha t^2$; $\omega^2 = \omega_0^2 + 2\alpha\theta$ |
| A point at r | $v = r\omega$; $a_t = r\alpha$; $a_c = r\omega^2$ |
| Inertia | $I = \sum mr^2$; $I = \int r^2\,dm$; $I = I_{CM} + Md^2$ |
| Torque | $\tau = rF\sin\varphi$; $\tau_{net} = I\alpha$ |
| Work | $W = \int \tau\,d\theta$; $W = \tau\Delta\theta$ (steady τ) |
| Energy, power | $K_R = \tfrac{1}{2}I\omega^2$; $P = \tau\omega$ |
| Heavy pulley | $a = (m_2 - m_1)g/(m_1 + m_2 + I/R^2)$ |
| Rolling | $v_{CM} = R\omega$; $\beta = I_{CM}/(mR^2)$ |
|---|---|
| Down a slope | $a = g\sin\theta/(1 + \beta)$; $v = \sqrt{2gh/(1 + \beta)}$ |
| Thick ring | $\beta = \tfrac{1}{2}(1 + (r_i/R)^2)$ |
| From a fall | $I = mr^2(g/a - 1)$ |
| Grip limit | $\tan\theta_{max} = \mu_s(1 + \beta)/\beta$ |
| Slipping | $a = g(\sin\theta - \mu_k\cos\theta)$; $\alpha = \mu_k mgR\cos\theta/I$ |
| Skid | $v_f = (v_0 - \beta R\omega_0)/(1 + \beta)$; $t = |v_0 - v_f|/(\mu_k g)$ |
| Spool | $\cos\varphi_c = r/R$ |
θ angle turned from the start (rad), $\bar{\omega}$ an average, ω angular velocity (rad/s), α angular acceleration (rad/s²), τ torque (N·m), I moment of inertia (kg·m²), β = I/(mR²) for a round body, $I_{CM}$ about the center of mass, d the distance between parallel axes, $r_i$ a ring’s inner radius, $\mu_s$ and $\mu_k$ the static and kinetic coefficients, $\omega_0$ in the skid formula counted positive for backspin, $\varphi_c$ the spool’s critical angle.
Sources and further reading
- OpenStax, University Physics Volume 1, by Samuel J. Ling, Jeff Sanny and William Moebs, §10.1–10.8 and §11.1, an open textbook (CC BY-NC-SA 4.0). The Walkthrough follows their order and notation.
- D. Kleppner and R. Kolenkow, An Introduction to Mechanics (2nd edition, Cambridge University Press, 2014), the chapters on rigid-body motion and angular momentum, for rigid-body motion, torques about a moving point and rolling with slipping.
- C. Frohlich, “What makes bowling balls hook?” American Journal of Physics 72, 1170 (2004).
- This sim’s Field Manual (H): the model, its engines and what it leaves out.
Rotational Dynamics & Rolling v1.3 · © 2026 Dr. David Meier · CC BY-NC-SA 4.0 · glidepathscience.org