RC Circuit Lab · Guide · glidepathscience.org
GuideRC Circuit Lab
Contents
This Guide covers the ideas and equations behind every Walkthrough step, Concept Challenge question and Predict round. Read Part 1 before the Intro track and Part 2 before the Advanced track, about ten minutes each. Come back whenever a question sends you here.
Part 1 · The essentials
The big idea
A capacitor's voltage cannot change in an instant: charge has to flow onto its plates through a resistance, and that takes time. So every RC circuit changes fast at first, then slower and slower, covering 63 % of the remaining change in each time constant, $τ = RC$. Know two instants and that one timescale, and you can sketch any curve in this lab before the simulator draws it.
What a capacitor does
A capacitor is two conductors, the plates, separated by an insulator. Connected to a battery, it gains $+Q$ on one plate and $-Q$ on the other, with
$Q = CΔV_C$
The capacitance C is in farads (F), coulombs per volt; this lab uses 0.1 µF up to a few thousand µF. No charge crosses the gap. Current flows to one plate and away from the other, so the loop carries a real current even though the circuit has a gap in it.
In parallel, capacitances add: $C = C_1 + C_2$. In series, $1/C = 1/C_1 + 1/C_2$, so the total is smaller than either; if they start uncharged, the smaller capacitor takes the larger voltage.
Two instants: just switched on, and a long time later
The loop rule shares the battery's emf ε between the resistor and the capacitor, where $q/C$ is the capacitor voltage $ΔV_C$:
$ε - IR - q/C = 0$
- Just switched on, C empty. $ΔV_C = 0$, so all of ε is across R and $I_0 = ε/R$. An empty capacitor acts like a wire, and C does not appear.
- A long time later, C full. $ΔV_C = ε$, nothing is left to drive current through R, and $I → 0$. A full capacitor acts like an open circuit.
The voltage across a capacitor cannot jump, since that would take an infinite current. The current through it can.
The time constant
$τ = RC$
Ohms times farads is seconds: Ω·F = (V/A)(C/V) = s. Kilo-ohms times microfarads is milliseconds. τ is proportional to both R and C: double either and everything takes twice as long; triple it, three times as long. In a series circuit, R and C set how fast the capacitor charges, not where it ends up: it always heads for ε.
Charging: 63 % per time constant
$ΔV_C(t) = ε(1 - e^{-t/τ})$ $I(t) = (ε/R)e^{-t/τ}$
Each τ closes 63.2 % of the gap that is left, so the voltage climbs quickly and then levels off. After five τ it is within 1 % of ε.
| time | τ | 2τ | 3τ | 5τ |
|---|---|---|---|---|
| $ΔV_C$, share of ε | 63.2 % | 86.5 % | 95.0 % | 99.3 % |
| I, share of $I_0$ | 36.8 % | 13.5 % | 5.0 % | 0.7 % |
The time to reach a fraction x of ε is $t = τ ln(1/(1 - x))$: half-way at 0.693 τ, 90 % at 2.303 τ.
Discharging and the half-life
With the battery switched out, the charged capacitor is the source, and the current runs the other way around the loop. Starting from $V_0$, the voltage and the current both decay:
$ΔV_C(t) = V_0 e^{-t/τ}$ $I(t) = -(V_0/R)e^{-t/τ}$
The minus sign means opposite to the charging current: the current jumps to $V_0/R$ the other way, then fades. Each quantity falls by the same factor in each equal interval, wherever it starts, so it halves every
$t_{1/2} = τ ln 2 ≈ 0.693\,τ$
a little less than τ. Two half-lives leave a quarter, not zero. The time to fall from $V_0$ to V is $t = τ ln(V_0/V)$.
Which resistance? Branches and switches
τ uses the resistance the capacitor sees. To find it, replace the battery by a wire, with the switches as they are now, and find the resistance between the capacitor's terminals. That can differ from the battery's path, and it changes when a switch moves. Take $R_1$ and C in one branch, $R_2$ straight across the battery, and the switch in the battery's main line:
- Switch closes, C empty. Both branches conduct at once, so the battery supplies $ε/R_1 + ε/R_2$. C charges through $R_1$ alone: $τ_{charge} = R_1C$. Once C is full, only $R_2$ conducts.
- Switch opens, C full. The only loop left runs from C through $R_1$ and $R_2$ in series, so $τ_{discharge} = (R_1 + R_2)C$, slower than the charge. Follow the loop out of the capacitor's + plate to see which way each current now runs.
Energy: the missing half
A capacitor at voltage V stores $U = ½CV^2$. Charging from empty to ε, the battery moves the charge Cε through its full emf and delivers $Cε^2$: twice what ends up stored. The other half becomes heat in the resistor, and it is exactly half whatever R is. A small R gives a big current for a short time, a big R a small current for a long time, and the two effects cancel. R sets how fast the heat appears, not how much.
Part 2 · Going further
The differential equation
With $I = dq/dt$, the loop rule is a first-order linear differential equation:
$R\,dq/dt + q/C = ε$ ⇒ $q(t) = Cε(1 - e^{-t/RC})$
Rearranged, $dq/(Cε - q) = dt/RC$; integrate from q = 0 at t = 0. One storage element gives a single exponential (add an inductor and the circuit can oscillate). The voltage starts rising at $dΔV_C/dt = I_0/C = ε/τ$, and that tangent line reaches ε at exactly t = τ: a second way to read τ off a graph.
Why the heat is ½Cε², whatever R
$\int_0^∞ I^2R\,dt = (ε/R)^2R\int_0^∞ e^{-2t/RC}\,dt = ½Cε^2$
R cancels. More generally, if C starts at $ΔV_{\mathrm{i}}$ and the supply steps to $ΔV_{\mathrm{f}}$, the resistor gets $½C(ΔV_{\mathrm{f}} - ΔV_{\mathrm{i}})^2$ by the time C settles. So charging in N equal steps, letting C settle after each one, wastes only $½Cε^2/N$. This "adiabatic charging" is used in some low-power logic circuits.
The resistance the capacitor sees: Thévenin
Seen from its two terminals, any network of batteries and resistors looks like one source $V_{th}$ in series with one resistance $R_{th}$, and the capacitor charges toward $V_{th}$ with $τ = R_{th}C$. $V_{th}$ is the terminal voltage with C removed; $R_{th}$ is the resistance between the terminals with each battery replaced by a wire. Across $R_2$ of a divider, $V_{th} = εR_2/(R_1 + R_2)$ and $R_{th} = R_1‖R_2$: in parallel, not in series. If the battery is then cut out, C discharges through $R_2$ alone. The Sandbox's Challenge Circuit, a resistor bridge, is solved the same way.
Charge sharing
Connect a charged $C_1$, at $V_0$, through a resistor to an empty $C_2$. The total charge is conserved and both end at the same voltage, $V_f = C_1V_0/(C_1 + C_2)$. Part of the energy $C_1$ gives up is stored in $C_2$; the drop in the two capacitors’ total, a fraction $C_2/(C_1 + C_2)$ of the energy at the start, becomes heat in the resistor, whatever R is. (As R approaches zero the wires' inductance takes over and the circuit rings.)
Meters change what they measure
A voltmeter is a resistor: about 10 MΩ for a digital meter, much less for an analog one. Across an isolated capacitor it is the only discharge path, so the reading decays with $τ = R_{meter}C$. Inside a circuit it sits in parallel with what it measures and shortens τ. A meter should have a hundred times or more the resistance it is connected across.
Square waves and filters
Compare τ with a square wave's half-period, T/2. If τ is much shorter, the capacitor follows the input with rounded edges. If τ is much longer, it settles at the input's average with a small, nearly triangular ripple. For a 0 → $V_0$ square wave, and for a sine wave of frequency f:
ripple (peak to peak) $= (V_{high} - V_{low}) tanh(T/4τ)$
sine gain $= 1/\sqrt{1 + (2πfRC)^2}$ $f_c = 1/(2πRC)$
Output across C makes a low-pass filter, which smooths. Output across R makes a high-pass filter, which passes fast changes: with τ much shorter than T/2, a square wave becomes spikes at its edges. At the corner frequency $f_c$ the sine gain is 0.707 (−3 dB) with a 45° lag, and well above $f_c$ it falls tenfold for every tenfold rise in frequency. The Sandbox's function generator has 50 Ω of output resistance, which adds to R in τ = (R + 50 Ω)C; CH1 is measured after it, so CH2/CH1 depends on R and C alone.
Reading τ from data
Taking logarithms turns a discharge into a straight line of slope −1/τ:
$ln ΔV_C = ln V_0 - t/τ$ $τ = (t_2 - t_1)/ln(V_1/V_2)$
Two readings fix the line: use their ratio, not their difference. With many readings, fit the best straight line to (t, ln V): its slope is −1/τ, so τ = −1/slope, and the scatter gives the uncertainty, as on the Lab Bench.
For the Mystery box, start with the capacitor fully discharged. The first-instant current gives $R = ε/I_0$. The time for the current to fall to 36.8 % of $I_0$ is τ, so $C = τ/R$. Round real readings to the nearest standard value.
Reference
Common mistakes
- "Full after one τ." It is 63 % of the way. Allow five τ to get within 1 %.
- "The same voltage every τ." Each τ closes 63 % of what is left.
- Putting C into the first-instant current. $I_0 = ε/R$; C only sets how long it lasts.
- Treating τ as the half-life. Half comes at 0.693 τ.
- Using the battery's path. Use the resistance the capacitor sees; it can change when a switch opens.
- Judging heat from $P = I^2R$ alone. The time the current flows grows with R too.
- Subtracting readings of an exponential. Use their ratio, or their logarithms.
- Forgetting the 2π. $f_c = 1/(2πRC)$, not $1/(RC)$.
- Assuming meters are ideal. A meter is a resistor, and can be the main discharge path.
Equation sheet
| Part 1 | |
|---|---|
| charge | $Q = CΔV_C$ |
| combined | $C_1 + C_2$ parallel; $1/C = 1/C_1 + 1/C_2$ series |
| loop rule | $ε - IR - q/C = 0$ |
| time constant | $τ = RC$ |
| first instant | $I_0 = ε/R$, $ΔV_C = 0$ |
| long time | $I = 0$, $ΔV_C = ε$ |
| charging | $ΔV_C = ε(1 - e^{-t/τ})$, $I = (ε/R)e^{-t/τ}$ |
| to a fraction x | $t = τ ln(1/(1 - x))$ |
| discharging | $ΔV_C = V_0 e^{-t/τ}$, $I = -(V_0/R)e^{-t/τ}$ |
| half-life | $t_{1/2} = τ ln 2 ≈ 0.693\,τ$ |
| two branches | charge $τ = R_1C$; discharge $τ = (R_1 + R_2)C$ |
| energy | $U = ½CV^2$; heat $½Cε^2$ |
| Part 2 | |
|---|---|
| ODE | $R\,dq/dt + q/C = ε$ |
| initial slope | $dV/dt(0) = ε/τ$ |
| heat in a step | $½C(ΔV_{\mathrm{f}} - ΔV_{\mathrm{i}})^2$ |
| Thévenin | $V_{th} = εR_2/(R_1 + R_2)$ |
| $R_{th} = R_1‖R_2$, $τ = R_{th}C$ | |
| sharing | $V_f = C_1V_0/(C_1 + C_2)$ |
| fraction lost | $C_2/(C_1 + C_2)$ |
| meter loading | $τ = R_{meter}C$ |
| from data | $τ = (t_2 - t_1)/ln(V_1/V_2)$ |
| ripple (p-p) | $(V_{high} - V_{low}) tanh(T/4τ)$ |
| low-pass corner | $f_c = 1/(2πRC)$ |
Symbols: ε battery emf (V) · R resistance (Ω) · C capacitance (F) · q, Q charge (coulombs) · I current (A) · $ΔV_C$ capacitor voltage (V) · τ time constant (s) · $t_{1/2}$ half-life (s) · U stored energy (J) · x a fraction of the final voltage · f, T drive frequency (Hz) and period (s) · $f_c$ corner frequency (Hz).
Further reading
Samuel J. Ling, Jeff Sanny and William Moebs, University Physics Volume 2 (OpenStax, 2016), free online under CC BY-NC-SA 4.0: Chapter 8, Capacitance; Section 10.5, RC Circuits; Chapter 15, Alternating-Current Circuits. And this lab's Field Manual (H): how the model works, and what it leaves out.
RC Circuit Lab v1.7 · © 2026 Dr. David Meier · CC BY-NC-SA 4.0 · glidepathscience.org