Inductance & LC Oscillations · Guide · glidepathscience.org
GuideInductance & LC Oscillations
Contents
This Guide explains the ideas and equations behind every Walkthrough step, Concept Challenge question and Predict round, in the order a textbook takes them. Part 1 prepares the Intro track and Part 2 the Advanced track; each takes about a quarter of an hour to read. Each section ends with a worked example that is not one of the sim’s own problems.
Part 1 · The essentials
Math you’ll need: algebra, square roots, powers of ten and the exponential $e^{x}$; the optional boxes use derivatives.
A circuit element that remembers its current
A resistor responds to the current through it right now. A capacitor responds to the charge it has collected. A coil (an inductor) responds to how fast its current is changing. Wind a wire into many turns and each turn sits in the magnetic field of all the others, so any change in the current changes the magnetic flux through the coil itself. Faraday’s law then induces an emf in the coil, and Lenz’s law fixes its direction: against the change. The result is a part that makes currents sluggish, stores energy in its magnetic field, and, paired with a capacitor, makes circuits ring.
Coils are everywhere a current must be smoothed, stored or switched: in power supplies and chargers, in the ignition coil of a car, in radio tuners and wireless chargers, and in every transformer.
Self-inductance and the back emf
Close a switch on a battery, a lamp and a large coil in series, and the lamp does not light at once: it comes up over a fraction of a second. As the current starts, the coil’s field grows, the flux through its own turns grows, and an emf is induced. By Lenz’s law that emf opposes the change that produces it, so while the current grows it pushes back. It is called a back emf. When the current falls, the induced emf reverses and pushes forward, trying to keep it going.
The flux through each turn is proportional to the current, so the total flux linkage $NΦ$ is proportional to $I$. The constant is the inductance:
$L = NΦ/I$
Its unit is the henry (1 H = 1 Wb/A = 1 V·s/A). Like capacitance, inductance belongs to the part, set by its turns, its shape and what fills it, never by the current. Faraday’s law turns it into the coil’s emf:
$ε_L = −L\,ΔI/Δt$
Here $ΔI/Δt$ is the rate of change of the current in amperes per second, taken over a time $Δt$ short enough that the rate is steady. A steady current, however large, induces nothing: once the current stops changing, an ideal coil is just a piece of wire.
A solenoid’s inductance
Inside a long solenoid of $N$ turns and length $ℓ$ the field is uniform, $B = μ_0NI/ℓ$, with $μ_0$ = 1.257 × 10⁻⁶ T·m/A. Each turn of area $A$ links $Φ = BA$, so
$L = μ_0N^2A/ℓ$
The number of turns appears squared: each turn helps make the field, and each turn links it. Twice the turns in the same length gives four times the inductance. An iron core multiplies $L$ by its relative permeability, often hundreds of times, which is how small coils reach henries.
The formula is for a long coil; a short one has less inductance, because its field spreads at the ends.
Rise, decay and the time constant
Put a coil $L$ and a resistor $R$ in series with a battery $ε$. Going round the loop, the battery’s emf is shared between the resistor and the coil: $ε = IR + L\,ΔI/Δt$, with $ΔI/Δt$ the current’s rate of change at that moment. At the instant the switch closes the current is still zero, so the resistor takes no voltage and the coil takes all of it: the current starts rising at $ε/L$. As it grows, $IR$ takes more of $ε$ and the rise slows. Long after, the current is steady at $ε/R$ and the coil takes nothing. The current follows
$I = (ε/R)(1 − e^{−t/τ})$ $τ = L/R$
The time constant $τ = L/R$ (H/Ω = s) sets the pace. After one $τ$ the current has reached $1 − e^{−1}$ = 63 % of its final value; after two, 86 %; after five, more than 99 %. A larger inductance makes it slower, a larger resistance faster: the opposite of an RC circuit’s $τ = RC$ for $R$. To measure $τ$ on a scope, find where the current reaches 63 % of its final value.
Now move the switch so the battery leaves the loop but the coil and resistor stay connected. The coil keeps the current going and it dies away with the same time constant:
$I = I_0e^{−t/τ}$
The inductive kick
A coil cannot change its current instantly: a finite change $ΔI$ in no time at all would make $ΔI/Δt$, and so the emf $L\,ΔI/Δt$, infinite. So when a switch opens on a coil carrying current, the coil keeps that current flowing for an instant through whatever path it can find, and its voltage rises as high as it must. If the only path is a resistor $R_p$ across the coil, the coil’s voltage jumps to $I(R + R_p)$ and the current dies within $L/(R + R_p)$. With no path at all, the voltage climbs until the air between the switch’s opening contacts conducts: the spark you may see when a motor or relay is switched off. A car’s ignition coil uses exactly this kick to fire the spark plug.
A diode across the coil, pointed so it carries nothing in normal use, gives the current a gentle path instead.
Energy in the magnetic field
While the current builds up, the battery pushes it against the back emf, and that work is stored. The back emf grows in step with the current, from 0 to its final size, so the stored energy is half the product, as with a capacitor:
$U_B = \tfrac12LI^2$
Doubling the current quadruples the energy. It is this energy that drives the kick, and that a flyback diode or a spark must dissipate. It lives in the magnetic field, with an energy density
$u_B = B^2/2μ_0$
in joules per cubic meter. For a long solenoid, $u_B$ times the volume inside is exactly $\tfrac12LI^2$.
The LC circuit
Charge a capacitor and switch it across a coil. The capacitor drives a current, but the coil makes it build up slowly. By the time the capacitor is empty the current is at its largest, and the coil will not let it stop: it keeps the current flowing, charging the capacitor the other way. Then the whole process runs back. With no resistance, the charge and the current oscillate for ever, at
$ω = 1/\sqrt{LC}$ $f = 1/(2π\sqrt{LC})$
The energy trades back and forth between the capacitor’s electric field, $q^2/2C$, and the coil’s magnetic field, $\tfrac12LI^2$, while the total stays fixed. When the capacitor is full the current is zero and all the energy is electric; a quarter period later the capacitor is empty, the current is largest and all the energy is magnetic. An eighth of a period from each extreme they hold half each.
A mass on a spring
The LC circuit and a mass on a spring obey the same equation. The capacitor’s charge plays the mass’s position, and the current, the rate at which the charge changes, plays its velocity. The coil, which resists changes in current, plays the mass, which resists changes in velocity; and $1/C$ plays the spring constant, since a small capacitor, like a stiff spring, pushes back hard for a little charge. The energies match too: $q^2/2C$ is the spring’s $\tfrac12kx^2$, and $\tfrac12LI^2$ is the mass’s $\tfrac12mv^2$. So the periods have the same form, and they are equal when $LC = m/k$:
$L ↔ m$ $1/C ↔ k$
Part 2 · Going further
Math you’ll need: derivatives and integrals, first- and second-order linear differential equations with constant coefficients, and logarithms.
Solving the RL equation
Kirchhoff’s loop rule for the series RL circuit is the first-order equation $L\,dI/dt + RI = ε$. Its solution from $I(0) = 0$ is the rise of Part 1, and with $ε = 0$ from $I(0) = I_0$ the decay. Every first-order circuit has this form; only the time constant changes. To find when the current reaches a fraction $f$ of its final value, solve $1 − e^{−t/τ} = f$:
$t = −τ\ln(1 − f)$
Each additional “9” in the fraction costs another $τ\ln 10$ ≈ 2.3$τ$: 90 % at 2.3$τ$, 99 % at 4.6$τ$, 99.9 % at 6.9$τ$.
Inductance from energy and geometry
Because $U = \tfrac12LI^2$, the inductance can be found from the field’s energy: $L = 2U/I^2$, with $U = ∫ (B^2/2μ_0)\,dV$ over all space. This route is often easier than the flux, because it needs no decision about which surface each turn bounds. For a toroid of $N$ turns on a core of rectangular section (inner radius $a$, outer $b$, height $h$), Ampère’s law gives $B = μ_0NI/2πr$ inside the core and nothing outside; integrating the flux through one turn gives
$L = μ_0N^2h\ln(b/a)/2π$
A coaxial cable is the same calculation between its conductors, $L′ = (μ_0/2π)\ln(b/a)$ per meter. A short coil’s field spreads at its ends; Wheeler’s formula, $L = μ_0πr^2N^2/(ℓ + 0.9r)$, is good to about 1 % for $ℓ > 0.8r$.
Mutual inductance and coupling
When the flux of one coil passes through another, a changing current in the first induces an emf in the second. The mutual inductance is the flux linkage in coil 2 per ampere in coil 1, $M = N_2Φ_{21}/I_1$, and $ε_2 = −M\,dI_1/dt$. For a coil of $N_2$ turns wound round the middle of a long solenoid, every turn links the solenoid’s whole flux:
$M = μ_0N_1N_2A/ℓ$ $|ε_2| = M\,dI_1/dt$
Neumann’s formula, $M = (μ_0/4π)∮∮ d\vec l_1·d\vec l_2/|\vec r_1 − \vec r_2|$, is symmetric in the two coils, so $M_{12} = M_{21}$ whatever their shapes: the easy direction gives the hard one. How much of one coil’s flux reaches the other is measured by the coupling coefficient, between 0 and 1:
$M = k\sqrt{L_1L_2}$
Two coils in series carry the same current, so their self and mutual emfs add: $L = L_1 + L_2 ± 2M$, plus when their fields aid, minus when they oppose. The difference between the two connections is $4M$, a way to measure it.
The LC equation
With $I = dq/dt$, the loop rule for an LC circuit is $L\,d^2q/dt^2 + q/C = 0$, the equation of simple harmonic motion. Starting from a full capacitor, $q = q_0\cos ωt$ and $I = −ωq_0\sin ωt$: the current is a quarter cycle out of step with the charge, largest when the charge passes through zero. Energy conservation gives the peak current directly, $\tfrac12CV^2 = \tfrac12LI_{max}^2$:
$I_{max} = V\sqrt{C/L}$
Plotted against each other, $q$ and $I$ trace an ellipse, the phase portrait of an undamped oscillator.
Damping and Q
Resistance adds a first-derivative term: $L\,q″ + Rq′ + q/C = 0$. Trying $q ∝ e^{st}$ gives $s = −R/2L ± \sqrt{(R/2L)^2 − 1/LC}$. Below the critical resistance the roots are complex and the circuit rings at $ω_d = \sqrt{ω_0^2 − (R/2L)^2}$ inside an envelope $e^{−Rt/2L}$ (underdamped); at it, the charge returns as fast as it can without overshooting (critically damped); above it, it creeps back (overdamped):
$R_c = 2\sqrt{L/C}$
The quality factor measures how lightly a circuit is damped: about 2π times the stored energy over the energy lost per cycle. The amplitude halves after $t_{1/2}$, about $Q\ln 2/π$ cycles:
$Q = (1/R)\sqrt{L/C}$ $t_{1/2} = 2L\ln 2/R$
Every real coil has wire resistance, and an iron core adds hysteresis and eddy-current losses; even a perfect circuit radiates a little. So no real LC rings for ever.
Coupled circuits and beats
Two identical LC loops whose coils share flux obey $Lq_1″ + Mq_2″ + q_1/C = 0$ and the same with 1 and 2 swapped. Adding and subtracting the two equations separates them into normal modes: the loops swinging together, with inductance $L + M$, and against each other, with $L − M$:
$ω_± = ω_0/\sqrt{1 ± k}$
Starting one loop alone is the sum of the two modes in equal parts. They drift in and out of step, so the energy beats across to the second loop and back. All of it is in loop 2 when the modes have slipped half a cycle:
$t = π/(ω_− − ω_+)$
For weak coupling that is about $1/(2k)$ periods. Tuned transformers in radios and wireless chargers work this way.
Switching and the flyback diode
A transistor or relay that switches a coil off must survive the kick. The standard protection is a flyback diode across the coil, its cathode toward the supply’s + side, so it is reverse-biased and carries nothing while the switch is closed. When the switch opens, the coil keeps its current flowing in the same direction, which drives the switch end below the supply’s − side; the diode turns on and carries the current round the coil and its resistance at about 0.8 V. The coil’s $\tfrac12LI^2$ is turned to heat in the diode and the wire, and the switch never sees more than the supply plus a diode drop. Switching power supplies use this deliberately: the coil’s stored energy is passed on, not wasted (the Buck & Boost Converters sim).
Reference
Common mistakes
Part 1
- Treating a coil like a capacitor: just after a switch closes a coil carries no current; long after it is a wire.
- Pointing the back emf against the current: it opposes the change, and pushes forward while the current falls.
- Thinking $L$ depends on the current: it depends on the turns, shape and core.
- Writing $τ = LR$: the time constant is $L/R$.
- Losing the ½ in $\tfrac12LI^2$, or forgetting to square the current.
- Giving $ω$ in rad/s when $f$ in Hz is asked: $f = ω/2π$.
- Matching $C$ to $k$ in the analogy: it is $1/C$ that plays the spring constant.
Part 2
- Taking $M$ from the turns ratio: reciprocity makes $M_{12} = M_{21}$.
- Counting the mutual term once in series: it is $±2M$.
- Halving the energy instead of the amplitude: the amplitude halves in $2L\ln 2/R$.
- Taking the beat period for the transfer time: loop 2 is full after half a beat.
The equation sheet
| Part 1 | |
|---|---|
| inductance | $L = NΦ/I$ |
| the coil’s emf | $ε_L = −L\,dI/dt$ |
| a long solenoid | $L = μ_0N^2A/ℓ$ |
| time constant | $τ = L/R$ |
| rise | $I = (ε/R)(1 − e^{−t/τ})$ |
| decay | $I = I_0e^{−t/τ}$ |
| energy | $U_B = \tfrac12LI^2$ |
| energy density | $u_B = B^2/2μ_0$ |
| LC | $ω = 1/\sqrt{LC}$ |
| LC frequency | $f = 1/(2π\sqrt{LC})$ |
| the analogy | $L ↔ m$, $1/C ↔ k$ |
| Part 2 | |
|---|---|
| time to a fraction | $t = −τ\ln(1 − f)$ |
| from energy | $L = 2U/I^2$ |
| toroid | $L = μ_0N^2h\ln(b/a)/2π$ |
| solenoid and coil | $M = μ_0N_1N_2A/ℓ$ |
| induced emf | $|ε_2| = M\,dI_1/dt$ |
| coupling | $M = k\sqrt{L_1L_2}$ |
| in series | $L = L_1 + L_2 ± 2M$ |
| peak current | $I_{max} = V\sqrt{C/L}$ |
| critical damping | $R_c = 2\sqrt{L/C}$ |
| quality factor | $Q = (1/R)\sqrt{L/C}$ |
| amplitude halves | $t_{1/2} = 2L\ln 2/R$ |
| normal modes | $ω_± = ω_0/\sqrt{1 ± k}$ |
| energy transfer | $t = π/(ω_− − ω_+)$ |
Symbols: $L$ inductance; $N$ turns; $Φ$ flux through one turn; $I$ current; $ε$ the battery’s emf; $R$ resistance; $τ$ time constant; $A$ a coil’s area and $ℓ$ its length; $μ_0$ = 1.257 × 10⁻⁶ T·m/A; $B$ the field; $U$ and $u$ energy and energy density; $C$ capacitance; $q$ charge; $V$ a starting voltage; $ω$ angular frequency, $f$ frequency; $m$ and $k$ a mass and spring constant; $M$ mutual inductance and $k$ (in Part 2) the coupling coefficient; $h$, $a$, $b$ a toroid’s height and radii; $Q$ the quality factor.
Sources and further reading
- OpenStax, University Physics Volume 2, chapter 14, “Inductance,” CC BY-NC-SA 4.0 (openstax.org): the order of topics and the notation.
- E. M. Purcell and D. J. Morin, Electricity and Magnetism, 3rd ed. (Cambridge, 2013), and D. J. Griffiths, Introduction to Electrodynamics, 5th ed. (Cambridge, 2023), chapter 7, for Neumann’s formula and the energy in fields.
- H. A. Wheeler, “Simple inductance formulas for radio coils,” Proc. IRE 16, 1398 (1928).
- This sim’s Field Manual (H) for the model and its limits; the RC Circuit Lab for the capacitor’s time constant; Simple Harmonic Motion for the mass on a spring.
Inductance & LC Oscillations v1.1 · © 2026 Dr. David Meier · CC BY-NC-SA 4.0 · glidepathscience.org