DC Circuit Lab · Guide · glidepathscience.org
GuideDC Circuit Lab
Contents
This Guide covers the ideas and equations behind every Walkthrough step, Concept Challenge question and Predict round. Read Part 1 before the Intro track and Part 2 before the Advanced track, about ten minutes each. Come back whenever a question sends you here.
Part 1 · The essentials
The big idea
A battery does not hand out a fixed supply of current. It holds a nearly fixed voltage across its terminals, and the circuit decides how much current flows. Charge is never used up anywhere: what flows into a bulb flows out of it. What the bulb takes is energy, which the charges carry from the battery and give up as light and heat. Two rules, charge conserved at every junction and energy conserved around every loop, decide every current in this lab.
Charge flows, energy is taken
Current is the rate at which charge passes a point, $I = ΔQ/Δt$, in amperes (coulombs per second). In a single loop there is nowhere else for the charge to go, so every ammeter in the loop reads the same current, before a bulb and after it. A potential difference is energy per charge: 1 V is 1 J/C. A part with ΔV across it and I through it takes energy at the rate
$P = IΔV$
(J/C × C/s = J/s = W). For a resistor this is also $I^2R$ or $ΔV^2/R$. The current speeds through the whole loop at once because the wires are already full of free electrons; each one drifts slowly, but the field that pushes them is set up everywhere in a tiny fraction of a second.
Ohm’s law
$ΔV = IR$
For a resistor the current is proportional to the voltage across it: double ΔV and I doubles. That proportionality is Ohm’s law, and a part that obeys it is ohmic. R, in ohms (V/A), is its constant. Volts over kilohms gives milliamperes. Not every part is ohmic: a real lamp filament’s resistance rises as it heats (Part 2).
Series, parallel and brightness
Parts in series share one path, so the same current flows through each, and their resistances add. Parts in parallel share the same two junctions, so the same ΔV sits across each, and their conductances add:
$R_{eq} = R_1 + R_2$ $1/R_{eq} = 1/R_1 + 1/R_2$
A parallel pair is smaller than either resistor alone; two equal ones make half. With identical constant-resistance bulbs, brightness follows power:
- Two in series on one battery: half the voltage and half the current each, so each gets a quarter of one bulb’s power alone.
- Two in parallel: each has the full battery voltage, so each is as bright as one alone, and the battery delivers twice the current. An ideal battery holds its voltage, not its current.
- A in series with B ‖ C: A carries the battery’s whole current and B and C split it, so A is the brightest and B and C, equally bright, get a quarter of A’s power each. Unscrew C and A and B are simply in series: A dims and B brightens.
Kirchhoff’s rules
Two conservation laws decide every circuit, including the ones that are neither series nor parallel:
$ΣI_{in} = ΣI_{out}$ $ΣΔV = 0$
The junction rule is charge conservation: in a steady circuit charge does not keep piling up where wires meet. The loop rule is energy conservation per coulomb: walk once around any closed loop and you come back to the potential you started at. Walking through a battery from − to + the potential rises by ε; walking through a resistor along its current it drops by IR. To use them, give each branch a current and an arrow (a wrong guess only comes out negative), write the junction rule, and write one loop equation per independent loop. A battery can carry current either way: one that is pushed backward, into its + terminal, is being charged.
Where meters go
An ammeter measures the current through itself, so it goes in series, in the branch you want, and it should have almost no resistance. A voltmeter measures the potential difference between its two leads, so it goes in parallel, across the part, and it should have a very large resistance; its red lead is the + one, and it reads V(red) − V(black). Swap their places and they misbehave in opposite ways. An ammeter across a part shorts it: the part goes dark and the meter reads a current that is not the part’s. A voltmeter in series blocks the current: the circuit goes dark and the meter reads nearly the whole emf.
Real batteries
A real battery behaves like an ideal emf ε in series with a small internal resistance r. When current flows, part of ε drops across r inside it, and the terminals show less:
$I = ε/(R + r)$ $ΔV_t = ε - Ir$
With no current the terminal voltage equals ε, which is why a voltmeter alone cannot tell a fresh cell from a “dead” one: as a cell runs down its r grows, while its emf barely changes. A short circuit draws $ε/r$. Plot $ΔV_t$ against I and you get a straight line: its intercept is ε and its slope is −r, which is how the Lab Bench measures them.
Part 2 · Going further
Nodal analysis and superposition
Pick one node as the reference, 0 V, and call the other node potentials unknowns. Write the junction rule at each unknown node with every current written as (difference in potential)/R. With one unknown node joined to batteries through resistors, this is Millman’s form:
$V = (ε_1/R_1 + ε_2/R_2)/(1/R_1 + 1/R_2 + 1/R_3)$
This sim solves every circuit that way: modified nodal analysis, one equation per node plus one per battery for its current, with ideal wires merged first. In a circuit of batteries and resistors every current and voltage is linear in the sources, so superposition holds: find the effect of each source alone, the others replaced by wires (ideal current sources by breaks), and add. Powers do not superpose, because power goes as $I^2$.
Thévenin and maximum power
Seen from any two terminals, a network of batteries and resistors acts like one source $V_{th}$ in series with one resistance $R_{th}$. $V_{th}$ is the open-circuit voltage between the terminals; $R_{th}$ is the resistance between them with every battery replaced by a wire. A load $R_L$ then draws
$I_L = V_{th}/(R_{th} + R_L)$
A source with internal resistance r delivers the most power to a load when $R_L = r$:
$P_{max} = ε^2/4r$ at $R_L = r$
At that match the efficiency is only 50 %: the same current heats r and the load equally. Power systems run far from it, with $R_L ≫ r$; matching is for weak signals.
Measuring without disturbing
A meter is part of the circuit. A voltmeter of resistance $R_m$ across $R_2$ of a divider replaces $R_2$ by $R_2‖R_m$ and reads low; it is honest only when $R_m$ is far larger than the resistance the circuit has there. An ammeter of resistance $R_A$ adds to its loop and reads
$I = ε/(R + r + R_A)$
An analog meter is built on a movement that reads full scale at $I_g$ through its own $R_g$. A shunt in parallel makes an ammeter for a larger current, and a multiplier in series makes a voltmeter; “20 kΩ/V” on its face is $1/I_g$:
$R_{sh} = I_gR_g/(I - I_g)$ $R_m = V/I_g - R_g$
A Wheatstone bridge compares an unknown with standards by a null: two dividers share a battery and a galvanometer joins their middles. At balance no current flows through it, so neither its resistance nor the battery’s ε and r enter:
$R_x = R_3R_2/R_1$
For small resistances the leads matter. A two-wire ohmmeter reads R plus both leads. A four-wire (Kelvin) connection drives the test current through one pair of leads and senses the voltage with another that carries no current, so the leads drop nothing.
Real filaments
A tungsten filament’s resistance rises steeply with temperature (in this model as $T^{1.2}$), so a lamp is not ohmic: cold, it has about a thirteenth of its hot resistance. Its I–V curve bends over. At half its rated voltage a filament runs cooler and lower in resistance, so two identical lamps in series each get more than a quarter of their rated power. To find the current through a lamp in series with a resistor, draw the resistor’s load line on the lamp’s curve; the circuit sits where they cross:
$I = (ε - ΔV)/R$
Switched on cold, a lamp draws an inrush current $ε/R_{cold}$ that falls over tens of milliseconds as the filament heats. Bulbs usually fail at that moment, and fuses for lamps and motors are often slow-blow.
Reference
Common mistakes
- “The bulb uses up current.” It uses energy; the current out equals the current in.
- “A battery gives a fixed current.” An ideal one gives a fixed voltage; the circuit sets the current.
- Halving the power in series. Two identical constant-resistance bulbs in series on an ideal battery each get a quarter of one alone’s power (real filaments, cooler and lower in resistance, about 35 %).
- Adding parallel resistances. Add their reciprocals; a parallel pair is smaller than either.
- “The first bulb is brighter.” Position along a series path changes nothing.
- Putting an ammeter across a part. It goes in series; across a part it shorts it.
- Reading ε at the terminals under load. The terminals show $ε - Ir$.
- Dropping a negative current. It means the current flows against your arrow.
- Adding powers source by source. Currents superpose; powers do not.
- Treating a filament as a fixed resistance. Its resistance rises about thirteenfold as it heats.
Equation sheet
| Part 1 | |
|---|---|
| current | $I = ΔQ/Δt$ |
| Ohm’s law | $ΔV = IR$ |
| power | $P = IΔV = I^2R = ΔV^2/R$ |
| series | $R_{eq} = R_1 + R_2$; the same I |
| parallel | $1/R_{eq} = 1/R_1 + 1/R_2$; the same ΔV |
| junction | $ΣI_{in} = ΣI_{out}$ |
| loop | $ΣΔV = 0$ |
| real battery | $ΔV_t = ε - Ir$, $I = ε/(R + r)$ |
| short circuit | $I = ε/r$ |
| Part 2 | |
|---|---|
| nodal (one node) | $V = (Σε/R)/(Σ1/R)$ |
| Thévenin | $I_L = V_{th}/(R_{th} + R_L)$ |
| maximum power | $P_{max} = ε^2/4r$ at $R_L = r$ |
| voltmeter | $R_2‖R_m$ |
| ammeter | $I = ε/(R + r + R_A)$ |
| shunt | $R_{sh} = I_gR_g/(I - I_g)$ |
| multiplier | $R_m = V/I_g - R_g$ |
| bridge | $R_x = R_3R_2/R_1$ |
| load line | $I = (ε - ΔV)/R$ |
| inrush | $I_0 = ε/R_{cold}$ |
Symbols: ε emf (V) · r internal resistance (Ω) · I current (A) · ΔV potential difference across a part (V) · V a node’s potential, from the reference (V) · R resistance (Ω) · $R_{eq}$ equivalent resistance · P power (W) · $ΔV_t$ terminal voltage · $V_{th}$, $R_{th}$ Thévenin voltage and resistance · $R_L$ load · $R_m$ a meter’s (or a multiplier’s) resistance · $R_A$ an ammeter’s resistance · $I_g$, $R_g$ a movement’s full-scale current and resistance · $R_{sh}$ shunt.
Further reading
Samuel J. Ling, Jeff Sanny and William Moebs, University Physics Volume 2 (OpenStax, 2016), free online under CC BY-NC-SA 4.0: Chapter 9, Current and Resistance; Chapter 10, Direct-Current Circuits, which the Intro track follows. Paul Horowitz and Winfield Hill, The Art of Electronics, 3rd ed. (Cambridge, 2015), for meters and four-wire measurement. And this lab’s Field Manual (H): how the model works, and what it leaves out.
DC Circuit Lab v1.2 · © 2026 Dr. David Meier · CC BY-NC-SA 4.0 · glidepathscience.org